background image

Rinnai 11 

RF1800 OIM

CLEARANCES, MANTELS, SURROUNDS, RECESSES & HEARTHS

Clearances

The appliance must be installed with the shown 

minimum clearances to combustible materials.

Mantles

A timber mantel may be installed above this appliance 

but must be within the grey area as shown here.

Timber Surrounds

As with mantels when a timber surround is to be fitted, 

ensure it complies with minimum timber clearances 

of 300mm above and 150mm to each side.

Recesses

If the appliance is to be installed into a recess the 

recess must comply with the limitations shown right.

NOTE

The same limitations apply to the sides 

of the appliance.

TV or Ornamentation Above The Heater

CAUTION

The installation of electrical appliances 

above and in the vicinity of the heater 

such as, but not limited to, Plasma 

TV, LCD TV, Home Theatre Screens, 

Speakers, etc. must comply with their 

manufacturers’ instructions.
It is the responsibility of the installer/

end-user to check the installation 

instructions of these items and to 

ensure the location is suitable.
This caution also extends to, but 

is not limited to, ornaments such 

as: Paintings, Prints, Photographs, 

Tapestries, Mirrors, Stuffed Animals, 

etc.
Rinnai does not take any responsibility 

for any damage occurring to any items 

installed above and in the vicinity of 

the heater.

IDEA

Use either a shelf or mantel below the 

TV or ornament or alternately you can 

construct a recess to mount TV or 

ornament on. 
Check the manufacturers installation 

instructions for these items and ensure 

the recess is suitable.

Hearths 

Although a solid hearth is not required, if the appliance 

is  to  be  installed  within  300mm  of  the  floor,  it  is 

recommended that protection is given to any flooring 

surface directly in front of the unit as the appliance 

produces a large amount of radiant heat and this 

might cause damage to flooring and furnishings that 

are too close.

300*

X

X

45°

Top Trim

Mantel

Wall

MANTEL MUST NOT EXTEND BEYOND THIS AREA

* NOTE THAT SIDE CLEARANCES CAN BE 

  REDUCED FROM 300MM TO 50MM

SIDE VIEW

100

45°

FIRE PROOF 

BOARD

FIRE PROOF BOARD FOR 

MINIMUM HEIGHT OF 300MM

RECESS MUST NOT

EXTEND BEYOND 

THIS AREA

When within 300mm of floor

300

300

1000

(Min)

500

(min)

1000

(Recommended

minium height)

1000

(min)

500

(min)

Содержание RF1800

























Отзывы: