Rinnai HD210E Скачать руководство пользователя страница 7

Rinnai 

Commercial Manifold Pack OIM

SAVE A SERVICE CALL

Check the items below before requesting a service. Service and parts charges may be incurred where it is found 

that there is no fault with the water heater and the issue is related to the plumbing installation or is due to the failure 

of water or electric supplies.

Insufficient or no hot water

Is the electricity supply 

connected?

Check that the isolating switch marked “HOT WATER” or “WATER HEATER” at the 

meter box is switched on. Check also that any isolating switches installed near the 

water heater are switched on.

Check the fuse or circuit breaker marked “HOT WATER” or “WATER HEATER” at 

the meter box. Repeated failure of fuse or tripping of circuit breaker indicates a fault 

which must be investigated by an authorised trades person.

Is  there  insufficient  gas 

supply for gas heater(s)?

Check gas is available and turned ‘ON’.
Check the isolation valve in the gas line is opened.
Refer to your plumber to ensure the gas line has been purged of air after installation.

Are you using more hot 

water than you think?

Often end users are surprised at the amount of hot water used, especially when 

showering. If the amount of hot water used during the day exceeds the capacity of 

the hot water system, it is likely that there will be insufficient hot water. Have your 

plumber install water saving fixtures and/or flow control or pressure limiting valves to 

reduce consumption.

Thermostat settings?

Check the temperature of hot water delivered with a thermometer placed under the 

closest outlet (usually the kitchen sink) on a non-tempered hot water line.

The temperature of the water delivered should be at least 55°C (allowing for heat 

losses in pipe work).

If  this  is  not  the  case,  the  temperature  may  need  to  be  increased.  Contact  your 

installer or Rinnai to discuss adjusting the temperature.

No water from the hot tap?

Restriction in the hot tap or failure of the cold water supply to the heater.

Check for water flow at the other hot taps and that the cold water isolation valve is 

fully open.

Are any of the heaters 

displaying an error code?

Refer to fault finding section of this manual.

Are  the  cold  water  filters 

clean on the gas water 

heater(s)?

Isolate  and  remove  the  water  filter  at  the  cold  water  connection  point.  Refer  to 

separate manual for the gas continuous flow water heater operation.

CARE & MAINTENANCE

Содержание HD210E

























Отзывы: