Rinnai HD210E Скачать руководство пользователя страница 5

Rinnai 

Commercial Manifold Pack OIM

WARNING

MANDATORY INSPECTION PRIOR TO INSTALLATION

Immediately report any damage or discrepancies to the Supplier of the appliance. This 

appliance was inspected and tested at the time of manufacture and packaging, and released for 

transportation without known damage. Upon receipt, inspect the exterior for evidence of rough 

handling in shipment. Ensure that the appliance is labelled correctly for the gas and electrical 

supply, and/or other services it is intended to be connected to.
For safety and warranty purposes, appliances that may be damaged or incorrect must not be 

installed or operated under any circumstances. Installation of damaged or incorrect appliances 

may contravene local government regulations. Rinnai disclaims any liability or responsibility 

whatsoever in relation to the installation or operation of damaged or incorrect appliances.

NOTICE TO VICTORIAN CONSUMERS

WARNING

This appliance 

MUST 

be installed by a person licensed with the Victorian Building Authority.

ONLY 

a licensed person will have insurance protecting their workmanship.

Make sure you use a licensed person to install this appliance and ask for your Compliance 

Certificate. 

For further information contact the Victorian Building Authority on 1300 815 127

SAFETY

WARNING

This appliance is 

NOT

 intended for use by persons (including children) with reduced physical, 

sensory or mental capabilities, or lack of experience and knowledge unless they have been given 

supervision or instruction concerning use of the appliance by a person responsible for their 

safety.
Children should be supervised to ensure that they 

DO NOT

 play with the appliance.

Any power leads from the water heater system components 

MUST

 be plugged into an external 

weatherproof electrical outlet. If the power supply cord of the system is damaged, it 

MUST

 be 

replaced by an authorised person in order to avoid a hazard, using genuine replacement parts 

available from Rinnai. Take care of not to touch the power plugs with wet hands.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or 

similarly qualified persons in order to avoid a hazard.

DO NOT

 touch the unit cover or the flue outlet.

DO NOT

 insert objects into the flue outlet.

DO NOT

 spray water directly into the flue outlet.

Keep, trees, shrubs, etc. well clear of the flue outlet.
On colder days steam may discharged from the flue 

 

outlet. This condition is normal for high efficiency 

 

appliances and does not indicate a fault.

DO NOT

 Spray aerosols in the vicinity of this appliance  

while it is in operation.

DO NOT

 use or store flammable materials in or near 

 

this appliance.

DO NOT

 place articles on or against this appliance.

DO NOT

 modify this appliance.

DO NOT

 store pool chemicals near this appliance.

HOT!

WARNINGS & IMPORTANT INFORMATION

Содержание HD210E

























Отзывы: