background image

Rinnai 11 

DD FP Solar Pre Heat System OIM

7.  Connect Temperature Sensor Leads

Connect  temperature  sensor  leads  as  shown  on  page  20  and  26.  Ensure  the  leads  are  protected  from 

sunlight. The sensors must be sealed in place with thermoplastic putty or silicon.

It is important that these leads are installed as specified. Failure to do so will lead to malfunction or lack of 

hot water.

8.  Fill the System

Ensuring the power supply to the pump is off; turn on a hot water outlet tap(s). Remove the screw from the 

pump to allow air to bleed out. Open the stop cock in the cold water mains supply line. The entire system will 

fill with cold water. Once the pump is no longer bleeding air, replace the screw and continue to bleed the air 

through the taps. 

Turn off the hot tap at the sink when water flows freely without air bubbles or air bursts.
Air should be bled from the collectors by temporarily loosening a fitting at the outlet of each collector array.

9.  Adjust Pump Speed

Adjust the pump to the speed specified on page 13.

10.  Check for Leaks

Check  all  connections  for  leakage  and  tighten  if  necessary. This  is  especially  important  for  all  fittings  in 

positions not easily accessed such as near the solar collectors. Operate the easing gear of both PTR and 

ECV valve at the storage cylinders to ensure these valves are functional.

CAUTION

If leaks are detected the system must be drained and leaks repaired before the system is 

refilled. If this is necessary, cover the solar collectors with packaging cardboard or a tarp to 

prevent them from heating which could result in steam or hot water being discharged from 

fittings

11.  Power up the Controller

Power up the controller, which should be factory set to the desired operating parameters, and observe for any 

unlikely immediate errors. An error at this point usually refers to something that has been missed during the 

installation procedure. Refer to the separate manual supplied with the controller for more details.

12.  Finishing the Installation

Ensure that the set temperature on the gas boosting is set to 60°C or above for a Demand Duo or 70°C or 

above for a Manifold Pack.

Ensure that the delivered temperature of the water to the building complies with all relevant regulations.

INSTALLATION 

Содержание Enduro SP200B

































Отзывы: