Rigol DS2000E Series Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 283

Rigol DS2000E Series Скачать руководство пользователя страница 35

Chapter 1 Quick Start

RIGOL

DS2000E User’s Guide

1-7

Probe Compensation

When the probe is used for the first time or when the probe compensation signal
does not match that shown in Figure 1-7, you should compensate the probe to match
the input channel of the oscilloscope. The non-compensated or poorly compensated
probe may cause measurement errors. The probe compensation procedures are as
follows:

1.

Perform Step 1, 2, 3, and 4 in "Function Inspection".

2.

Check the displayed waveforms and compare them with the following figures.

Figure 1-8 Probe Compensation

3.

Use a nonmetallic driver to adjust the low-frequency compensation adjustment
hole on the probe until the waveform is displayed as "Perfectly compensated" in
the figure above.

Over compensated Perfectly compensated Under compensated

«
...
33
34
35
36
37
...
»

Содержание DS2000E Series




























































































































































































































































































Отзывы:

Нет отзывов