Rigol DS2000E Series Скачать руководство пользователя страница 260 | Manualshive

Страница: 260 / 283

Rigol DS2000E Series Скачать руководство пользователя страница 260

RIGOL

Chapter 14 Remote Control

DS2000E User’s Guide

14-2

Remote Control via USB

1.

Connect the device
Use a USB cable to connect the oscilloscope with your PC via the USB Device
interface.

2.

Install the USB driver
This oscilloscope is a USB-TMC device. After you connect the oscilloscope to the
PC and turn both on for the first time (the oscilloscope is automatically
configured to USB interface; at the same time, make sure that Utility



IO

Setting



USB Device is set to "Computer"), the Found New Hardware

Wizard as shown in the figure below is displayed on the PC. Please install the
"USB Test and Measurement Device (IVI)" driver following the directions in the
wizard. The steps are as follows.

1

2

«
...
258
259
260
261
262
...
»

Содержание DS2000E Series




























































































































































































































































































Отзывы:

Нет отзывов