Rigol DS2000E Series Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 283

Rigol DS2000E Series Скачать руководство пользователя страница 32

RIGOL

Chapter 1 Quick Start

1-4

DS2000E User’s Guide

To Prepare the Oscilloscope for Use

To Adjust the Supporting Legs

Adjust the supporting legs properly to use them as stands to tilt the oscilloscope
upwards for stable placement of the oscilloscope as well as better operation and
observation.

Figure 1-3 To Adjust the Supporting Legs

To Connect to AC Power

The power requirements of the oscilloscope are 100-240 V, 45-440 Hz. Please use
the power cord provided in the accessories to connect the oscilloscope to the AC
power source, as shown in the figure below. When the oscilloscope is connected to
power, the Power key

located at the lower-left corner of the front panel is

blinking.

Figure 1-4 To Connect to AC Power

Power Cord Connector

«
...
30
31
32
33
34
...
»

Содержание DS2000E Series




























































































































































































































































































Отзывы:

Нет отзывов