Rigmaster MTS-T4-LGN Скачать руководство пользователя страница 27

Страница: 27 / 56

LGN Owner's Manual

Cabin Controller

Page 25

LGN-Owners-Manual-071520

CODE

REMEDY/CAUSE

REMEDY/COMMENT

Error Code 20

Water Valve
Overcurrent

Electronic coolant
control valve drawing
excess amperage.

•

Unplug J2 connector, turn
POWER ON again. Code
should not display when J2 is
unplugged.

Error Code 21

GP Overcurrent

Glow plug relay
drawing excess
amperage.

•

Glow plug relay operation is
faulty or wire broken.

Error Code 22

Run or GP
Overcurrent

Run solenoid or glow
plug relay drawing
excess amperage.

•

Unplug run solenoid; power
with jumper wire; attempt again.
If code returns, glow plug relay
problem.

Error Code 23

Run Overcurrent

Run solenoid is drawing
excess amperage.

•

Unplug run solenoid; power
with jumper wire; attempt again;
measure Amps. If code
returns, broken wire.

Error Code 24

Start or Run
Overcurrent

Starter relay or run
solenoid drawing
excess current.

•

Unplug run solenoid; power
with jumper wire; attempt again.
If code returns, starter relay
problem.

Error Code 25

AC or Run
Overcurrent

A/C clutch or run
solenoid drawing
excess current.

•

Unplug run solenoid; power
with jumper wire; attempt again.
If code returns, A/C clutch
problem.

Error Code 26

BH Overcurrent

Phantom Code

– block

heater is not operated
by power module
output.
(no output on J1 Pin
#7).

•

May indicate damage to power
module circuit board. Possible
solution: Unplug J1 connector
for 30 seconds.

Error Code 27

Power down to
clear overcurrent

Power must be turned
off with the power
button then turned back
on.

•

This message appears if engine
start is attempted without
turning POWER OFF. Turn
power OFF then ON.

Содержание MTS-T4-LGN

























































Результаты поиска

Содержание MTS-T4-LGN

Отзывы:

Похожие инструкции для MTS-T4-LGN

Бренды по названию

Популярные бренды

Rigmaster MTS-T4-LGN, Руководство пользователя

Результаты поиска

Содержание MTS-T4-LGN

Отзывы:

Похожие инструкции для MTS-T4-LGN

Бренды по названию

Популярные бренды