manualshive.com logo in svg

Riello MCM 10, Технические характеристики

Поделиться
Скачать
Riello MCM 10 Скачать руководство пользователя страница 33

 

 

 

 

 

MULTI SENTRY 

 

 

SPTMSTD2T16EREN

 

31

 

b)

 

Transformer located outside the UPS

 (depending on the requirements and the type of electrical set up  

described below). 

This option can be applied to the entire 10÷40 kVA range. 
 

Note:

 

The presence of the transformer inside  the UPS changes the neutral system. The eventual installation of a 

"maintenance bypass remote" in parallel to the UPS is incompatible with the presence of the transformer. If it is still 
inserted by pass the remote maintenance, make sure that simultaneously with the closing of the switch by-pass 
the UPS is insulated from the plant by opening the disconnectors of input / output.

 

 
Electric connections diagrams 

The following drawings just provide a general overview of the possible installation scenarios. 
Every configuration should be carefully evaluated according with the real installation environment. 

 
Note:

  the  presence  of  the  transformer  will  modify  the  neutral  arrangements  of  the  installation.  The  eventual 

installation of a "remote maintenance bypass" to the insulation of the UPS, in case of breakdown / maintenance 
will take place after the transformer (if the same is installed in the UPS input) or upstream of the transformer (if the 
same is installed in the UPS output). 

 

UPS with no variation neutral condition 

 

 

UPS with Galvanic insulation on the input 

 

 

UPS with Galvanic insulation on the output 

 

 
 

Содержание MCM 10

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды