Riello FAMILY CONDENS 2.5, Инструкция по установке и эксплуатации

Страница: 33 / 88

FAMILY CONDENS IS E
32
ENGLISH
33
2. Display only of the RESET icon
Press the
key to restore operation. If the boiler performs the firing
procedure and resumes normal operation, the stoppage can be at-
tributed to a chance situation.
Repeated lockouts require the intervention of the Riello Technical
Assistance Centre.
3. Displaying the RESET icons and requires the intervention of
the Riello Technical Assistance Centre
Fault on the domestic hot water circuit probe - 60: the fault code
is only displayed in standby. Fault J0-J1 (faults regarding connec-
tions to the board) requires the intervention of the Riello Technical
Assistance Centre
Fault J0 - J1 (card connection faults): the intervention of the Riello
Technical Assistance Centre is needed.
O - Resetting the faults
Only the icon lights up, and the alarm code appears:
table 1
TEMPORARY FAULTS
CODE DESCRIPTION
11 Parasite flame
13 Minimum gas input pressure
25 Delivery probe limit temperature
27 Return probe limit temperature
41 Insufficient system pressure
60 Domestic hot water probe
75 Second heating system probe absent
77 Low temperature thermostat
78 Outlet-return differential
81 System fault
83 System fault
91 Cleaning the primary heat exchanger
For the “insufficient system pressure” fault, carry out the sys-
tem filling operations described in the Special functions chap-
ter. For fault 91, request the Riello Technical Assistance Centre
intervention.
The RESET icons light up, and the alarm code appears:
table 2
RESETTABLE FAULTS PRESS THE RESET BUTTON
CODE DESCRIPTION
10 No flame lockout
14 Minimum gas input pressure
20 Limit thermostat
24 Delivery probe limit temperature
26 Return probe limit temperature
34 Fan (cycle start)
40 Insufficient system pressure
79 Outlet-return differential
The RESET and icons light up, and the alarm code appears:
table 3
CALL THE TECHNICAL SERVICE
CODE DESCRIPTION
21 Flue gas probe
28 Outlet-return probe differential
29 Flue gases probe overtemperature
37 Fan operating (high rpm)
42 Water pressure transducer
50-59 Electronic card
70 Primary probe short-circuit/open
72 Return probe short circuit/open
80 System fault
82 System fault
P - Regular scheduled maintenance
OPERATIONS
1st
YEAR
2nd
YEAR
Inspection of sealing components
°
°
Cleaning of the primary heat exchanger flue gases side
°
°
Cleaning of the combustion chamber,
fan and venturi tubes
°
°
Checking of the water and gas safety devices
°
°
Checking the gas output and make any adjustments
°
°
Checking the draught and flue gases pipe
°
°
Cleaning of the burner and checking its firing
°
°
Checking the hydraulic operations ° °
Combustion analysis
-
°
Checking and lubricating the hydraulic unit components
-
°
Checking the system seals
-
°
Washing of the heat exchanger
-
°
Checking the efficiency of the electric
and electronic components
-
°
FAN EFFICIENCY (only for vacuum chamber versions) ° °
Checking the condensate discharge system ° °
CHECKING THE CONDENSATE
NEUTRALISER (if installed)
° °
NOTE: the maintenance operations described above, must be car-
ried out every two years in accordance with regulations in force.
Q - Cleaning
The only cleaning operations that we recommend are those involving
the external boiler panels, which should be cleaned using just a cloth
dampened with soap and water.
In the case of stubborn marks, dip the cloth in a mixture of 50% water
and methylated spirits, or use specific products.
Do not use fuels and/or sponges soaked in abrasive solutions
or powder detergents.
It is forbidden to carry out any cleaning operations before dis-
connecting the boiler from the mains electricity supply; to do
this, turn the main system switch to “off”.