Riello UPS Sentinel Tower STW 10000 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 40

background image

36



Faults:

These are more critical problems compared to the “Anomalies”, as if they persist they may bring the UPS to

a halt even in a very short time.

CODE

DESCRIPTION

F01

Internal communication error

F03

Phase1 input fuse blown

F04

Phase2 input fuse blown or input relay locked (will not close)

F05

Phase3 input fuse blown or input relay locked (will not close)

F09

Precharge of positive branch condensers failed

F10

Precharge of negative branch condensers failed

F11

BOOST stage anomaly

F14

Inverter Phase1 sine curve distorted

F17

Inverter stage anomaly

F19

Positive battery overvoltage

F23

Output overload

F26

Phase1 output relay locked (will not open)

F29

Phase1 output fuse broken or output relay locked (will not close)

F32

Battery charger stage anomaly

F33

Battery measures error

F34

Heat sink overtemperature

F37

Battery charger overtemperature

F39

VDC Bus measures error

F40

Fan failure

F41

Redundant Bypass failure



Locks:

these codes indicate that the UPS, or one of its parts, is locked. Usually, they are preceded by an alarm signal.

In case of faults and consequent locking of the inverter, the latter will be turned off and the load will be powered via
the bypass line (this procedure is excluded for locks caused by serious and persistent overloads and for those caused
by a short circuit).

CODE

DESCRIPTION

L01

Incorrect auxiliary power supply

L02

One or more internal cables disconnected

L03

Phase1 input fuse broken

L04

Phase2 input fuse broken or input relay locked (will not close)

L05

Phase3 input fuse broken or input relay locked (will not close)

L06

BOOST stage overvoltage positive

L07

BOOST stage overvoltage negative

L08

BOOST stage undervoltage positive

L09

BOOST stage undervoltage negative

L10

Static bypass switch fault

L11

L1 bypass output locked

L14

Phase1 inverter overvoltage

L17

Phase1 inverter undervoltage

L20

Continuous voltage at inverter output or Sine curve of Phase1 inverter distorted

L23

Phase1 output overload

L26

Short circuit at Phase1 output

L34

Phase1 heat sink overtemperature

L37

Battery charger overtemperature

L38

Temperature probe 1 damaged

L39

Temperature probe 2 damaged

L41

Battery charger temperature probe damaged

L49

Inverter capacitor damaged

«
...
34
35
36
37
38
...
»

Содержание Sentinel Tower STW 10000









































Отзывы:

Нет отзывов

Похожие инструкции для Sentinel Tower STW 10000

Бренд: OBR Страницы: 92

Referenz AC-A3016

Бренд: Inakustik Страницы: 24

Arteor 5 735 49

Бренд: LEGRAND Страницы: 3

SASILplus-MOT Series

Бренд: JEAN MÜLLER Страницы: 12

Бренд: HP Страницы: 7

252663-B24 - PDU Power Distribution Strip

Бренд: HP Страницы: 8

Бренд: HP Страницы: 19

unimes H U-PW powerway

Бренд: hager Страницы: 82

Portable Power Distribution Box

Бренд: Mennekes Страницы: 24

Battery Protect BP 200

Бренд: Victron energy Страницы: 21

Бренд: Tripp Lite Страницы: 6

STROHM SMCUB-027W-3M

Бренд: Hornbach Страницы: 2

T009-5030 Series

Бренд: Amphenol Страницы: 16

Бренд: Samson Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды