background image

4 – English

 

Know your air compressor. 

Read operator’s manual 

carefully. Learn its applications and limitations, as well 
as the specific potential hazards related to this product. 
Following this rule will reduce the risk of electric shock, 
fire, or serious injury.

 

Drain tanks of moisture after each day’s use. 

If unit will not be used for a while, it is best to leave drain 
valve open until such time as it is to be used. This will 
allow moisture to completely drain out and help prevent 
corrosion on the inside of tanks.

 

Risk of Fire or Explosion.

 Do not spray flammable liquid 

in a confined area. Spray area must be well ventilated. Do 
not smoke while spraying or spray where spark or flame 
is present. Keep compressors as far from the spraying 
area as possible, at least 15 feet from the spraying area 
and all explosive vapors.

 

Risk of Bursting. 

Do not adjust regulator to result in 

output pressure greater than marked maximum pressure 
of attachment. Do not use at pressure greater than 150 psi.

 

If connected to a circuit protected by fuses, use time-
delay fuses with this product.

 

To reduce the risk of electric shock,

 do not expose to 

rain. Store indoors.

 

Inspect tanks yearly for rust, pin holes, or other 
imperfections that could cause it to become unsafe. 

Never weld or drill holes in the air tanks.

 

Make sure the hose is free of obstructions or snags.

 

Entangled or snarled hoses can cause loss of balance or 
footing and may become damaged. 

 

Use the air compressor only for its intended use. Do 
not alter or modify the unit from the original design 
or function.

 

Always be aware that misuse and improper handling of 

this product can cause injury to yourself and others.

GENERAL SAFETY RULES

SPECIFIC SAFETY RULES

 

Never  leave  a  tool  unattended  with  the  air  hose 

attached.

 

Never point any air tool toward yourself or others.

 

Do  not  operate  this  air  compressor  if  it  does  not 

contain a legible warning label.

 

Do not continue to use a tool or hose that leaks air or 

does not function properly.

 

Always disconnect the air supply and power supply 

before making adjustments, servicing a product, or when 
a product is not in use.

 

Do not attempt to pull or carry the air compressor by 
the hose.

 

Your tool may require more air consumption than this 
air compressor is capable of providing.

 

Always follow all safety rules recommended by the 

manufacturer of your air tool, in addition to all safety 
rules for the air compressor. 

Following this rule will 

reduce the risk of serious personal injury.

 

Never direct a jet of compressed air toward people or 

animals. Take care not to blow dust and dirt towards 
yourself or others. 

Following this rule will reduce the risk 

of serious injury.

 

Do not use this air compressor to spray chemicals. 

Your lungs can be damaged by inhaling toxic fumes. A 
respirator may be necessary in dusty environments or 
when spraying paint. Do not carry while painting.

 

Inspect product cords and hoses periodically and, if 
damaged, have repaired at your nearest Authorized 
Service Center. Constantly stay aware of cord location. 

Following this rule will reduce the risk of electric shock or 
fire.

 

Never use an electrical adaptor with this grounded 

plug.

 

Keep the exterior of the air compressor dry, clean, and 
free from oil and grease.

 Always use a clean cloth when 

cleaning. Never use brake fluids, gasoline, petroleum-
based products, or any strong solvents to clean the unit. 
Following this rule will reduce the risk of deterioration of 
the enclosure plastic.

SERVICE

 

When servicing a product, use only identical 
replacement parts. Follow instructions in the 
Maintenance section of this manual.

 Use of unauthorized 

parts or failure to follow Maintenance instructions may 
create a risk of injury.

 

Service must be performed only by qualified repair 

personnel. 

Service or maintenance performed by 

unqualified personnel may result in a risk of injury.

 

Disconnect power supply, open drain valve to decom-

press tanks and allow water to drain, and allow air 

compressor to become cool to the touch before 

servicing. 

Turn pressure regulator knob fully counter-

clockwise after shutting off air compressor.

Содержание OF60150VP













































Отзывы: