manualshive.com logo in svg

Ridetech LevelTow 81234006, Руководство пользователя

Поделиться
Скачать
Ridetech LevelTow 81234006 Скачать руководство пользователя страница 5

The LevelTow Compressor System is an automatic leveling system, once it is turned on(button 
illuminated blue) it will operate without any assistance.

     
to keep the vehicle level. It has a dwell range built in so that when the truck is going down the 
road hitting small defects the system will be idle.  It isn’t until the sensor gets out of this dwell 
range for 18 seconds that the system will react.

The activation switch has to be illuminated blue for the system to work.

 

  Activation 

Button

1. Before you install the compressor system, 
you will need to have the helper Airsprings 
installed.  This will ensure that the LevelTow 
linkage does not get in the way of the Air-
springs.

         
vehicle at ride height, measure the lip of 
the fender to the ground at the center of the 
wheel and write it down.
Measurement_________________
This measurement will be used as a refer-
ence once you have the compressor system 
installed.

2. Unpack the wiring for the LevelTow sys-
tem and lay it out.  This will give you an idea 
to where you can mount the components 
without having to modify the wiring harness.

NOTE:

There is a wiring diagram on Page 7 to assist 
you in component location.

Red W

ire

20 Amp

Fuse

Activation 

Switch

Manual

Inflate/Deflate

GREEN

BLA
CK

BL

UE

White

4 pin plug

Black

10 pin plug

Gray

4 pin plug

Relay

Black 3 pin plug

Black Wire

Black Wire

System
Ground

Y

e

llow Wire

Battery 

(Needs to go to Battery under hood)

Keyed Power

(Should only have power with key on)

(these wires

can be attached

at the same point)

Page 5

Содержание LevelTow 81234006













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды