manualshive.com logo in svg

Ridetech LevelTow 81234006, Руководство пользователя

Поделиться
Скачать
Ridetech LevelTow 81234006 Скачать руководство пользователя страница 12

Manual Operation:

The LevelTow Compressor System also has a manual control function.  This function allows you to manually 
   
 =    
<  

Note:

If the Activation Button is illuminated blue and the manual button is pushed the truck will relevel itself.  The 
activation button has to be off for the manual control to be used and the truck remain at the height.

Troubleshooting:

$   <   
direction.  You can verify this by turning the truck on and check that the activation button is illuminated blue. 
Unhook one end of the linkage and move the sensor arm by hand.  If when you move the arm down (Keep in 
 @JQ      
VX      !
ness at the sensor.  To do this, with the truck turned off,  simply unplug the harness from the sensor.  Using 
a small screwdriver pop the purple retainer out of the plug by prying up on each end of it.  After removing the 
retainer if you look into the end of the plug you will see a tang holding each wire terminal.  Simply pry it down 
just enough to release the terminals of the blue and green wires.  Swap the blue and green wire postion and 
reinstall the wires into the plug paying attention to the direction of the small tab on the wire terminal.  This 
tab will point to the center of the plug.  Push the wire terminals into the plug making sure they catch on the 
    Q      
  <  Q  $
correctly, shut the truck off and reattach the linkage. 

STILL HAVE QUESTIONS?

Tech line hours

Monday-Friday

8AM - 6PM (EST)...........812-482-2932

Page 12

#82010009

RED

RED

BLACK

BLUE

GREEN

VIEW FROM WIRE SIDE

WIRE SIDE

SIDE VIEW

WIRE LOCATIONS AT HEIGHT SENSOR

Содержание LevelTow 81234006













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды