Ricoh Pro 1106EX Скачать руководство пользователя страница 223

Страница: 223 / 234

Supplementary Information

203

❖

Combine

• In this mode, the machine selects the reproduction ratio automatically.

This reproduction ratio depends on copy paper sizes and the number of
originals.

• The reproduction ratios you can specify are 25 - 400%.
• If the calculated ratio is under the minimum ratio, it is automatically ad-

justed to within available range. However, with some ratios, parts of the
image might not be copied.

• You cannot use custom size paper.
• If the orientation of originals is different from that of the copy paper, the

machine will automatically rotate the image by 90

to make copies properly.

• If the number of originals placed is less than the number specified for com-

bining, the last page segment is left blank as shown.

❖

Booklet/Magazine

• The machine sets the reproduction ratio automatically to meet the paper

size and copies the originals together onto the paper.

• The reproduction ratios you can specify are 25 - 400%.
• If the calculated ratio is under the minimum ratio, it is automatically ad-

justed to within available range. However, with some ratios, parts of the
image might not be copied.

• If the orientation of originals is different from that of the copy paper, the

machine will automatically rotate the image by 90

to make copies properly.

• You cannot copy with originals different in size and orientation.
• If the number of originals scanned is less than a multiple of 4, the last page

is copied blank.

• In Magazine mode, the copying may take some time after scanning originals.
• When the optional booklet finisher is installed, if you select

[

Staple: Center

]

in Magazine mode, the machine staples and folds the paper in the center,
then delivers the paper folded.

❖

Image Repeat

• Depending on the paper size, ratio, and orientation, parts of repeated im-

ages may not be copied.

❖

Centering

• Though the original is set to a different orientation from the paper loaded,

the machine will not rotate the image by 90

(Rotate copy).

Содержание Pro 1106EX











































































































































































































































Результаты поиска

Содержание Pro 1106EX

Отзывы:

Похожие инструкции для Pro 1106EX

Бренды по названию

Популярные бренды

Ricoh Pro 1106EX, Руководство по эксплуатации

Результаты поиска

Содержание Pro 1106EX

Отзывы:

Похожие инструкции для Pro 1106EX

Бренды по названию

Популярные бренды