Ricoh FAX4800L Скачать руководство пользователя страница 227

Страница: 227 / 334

Problem

Action Required

Frequent original misfeeds.

Multifeeds

Incorrect positioning of originals

•

Put the document in the feeder correctly.
See page 16.

Incorrect alignment of originals

•

Align the edges of the document. See page 16.

Curled pages

•

Flatten the document. See page 13.

Incorrect document type

•

Use a proper document type. See page 13.

Mixed document types

•

The pages must all be of the same type.

Static electricity on the originals

•

Shuffle the document. See page 16.

User maintenance is needed

•

Do user maintenance, especially separation pad [A].
See page 188.

The document feeder is not adjusted correctly.

•

Adjust the auto document feeder. See page 202.

Non-feeds

Copier silicone oil on the originals

•

Wait a few minutes, then try again.

Incorrect alignment of originals

•

Align the edges of the document. See page 16.

Curled pages

•

Flatten the document. See page 13.

Incorrect document type

•

Use a proper document type. See page 13.

More than 50 pages in the feeder

•

Do not place more than 50 pages in the automatic
document feeder at once.

User maintenance is needed

•

Do user maintenance, especially separation pad [A] and

roller [E].

See page 188.

The document feeder is not adjusted correctly.

•

Adjust the auto document feeder. See page 202.

Transmission cannot take
place; CLEAR ORIGINAL
appears.

The document is jammed in the feeder.

•

Remove the jammed document (see page 201)
and repeat the transmission procedure.

The document may be longer than the maximum limit
(see page 12).

•

Make sure that none of your originals exceed this
limit.

Do user maintenance, especially separation pad [A] and roller
[F] (see page 188).

•

If the same problem still exists after user
maintenance, adjust the auto document
feeder mechanism (see page 202).

OPERATING DIFFICULTIES

SOLVING PROBLEMS

212

Содержание FAX4800L















































































































































































































































































































































Результаты поиска

Содержание FAX4800L

Отзывы:

Похожие инструкции для FAX4800L

Бренды по названию

Популярные бренды

Ricoh FAX4800L, Руководство оператора

Результаты поиска

Содержание FAX4800L

Отзывы:

Похожие инструкции для FAX4800L

Бренды по названию

Популярные бренды