Ricoh AP610N - Aficio B/W Laser Printer Скачать руководство пользователя страница 75

Страница: 75 / 124

G1128611A_1.10

2004, 2005

Troubleshooting

Error & Status Messages on the Control
Panel

This section explains what the messages that appear on the control panel mean
and what to do when a particular message appears.

❖

Messages (in alphabetical order)

Messages/Second

messages

Description

Solution

Call Service: EC

Power Off On

/ If Error Reoccur

Call Service

An error A communication error
sent from the engine to the con-
troller has occurred in the print-
er.

Turn the power off, and then on. If the
message appears again, call your
sales or service representative.

Cannot check

Signal in Ad hoc

An attempt to check the radio
signal was made while the
communication mode was set
to

[

802.11 Ad hoc

]

in the interface

settings.

To check the radio signal , select In-
frastructure in the communication
mode settings.

Change Setting

Tray #

/ Paper Size:

Paper Type:

The paper size and type setting
in the tray differs from that of
actual paper size and type in
the tray.

#: tray number

Load paper of the selected size in the
tray, and then change the paper size
setting with the control panel. Or,
press

{

Form Feed

}

, and then select the

tray using the control panel. Or, press

{

Job Reset

}

to cancel the print job.

You can make to setting to print disre-
garding the error message.

Close Duplex

Unit Cover

The cover of the optional du-
plex unit is open.

Close the cover of the optional duplex
unit.

Front Cover

The front cover is open.

Close the front cover.

Close Rear/Paper

Exit Cover

The paper exit cover or the rear
cover is open.

Close the paper exit cover or the rear
cover.

Collate Cancelled

The collate feature has been
cancelled.

Increase the RAM capacity.

DHCP assigned

Cannot change

An attempt to change the IP ad-
dress, subnet mask or gateway
address was made while DHCP
was set to

[

]

Make the change after setting DHCP
to

[

Off

]

Driver Setting

Error (Memory)

The printer identified a down-
load error. This error may occur
when the installed memory
amount is less than the driver
setting.

Verify that the proper memory size is
specified via the driver setting.

Содержание AP610N - Aficio B/W Laser Printer





























































































































Результаты поиска

Содержание AP610N - Aficio B/W Laser Printer

Отзывы:

Похожие инструкции для AP610N - Aficio B/W Laser Printer

Бренды по названию

Популярные бренды

Ricoh AP610N - Aficio B/W Laser Printer, Руководство по обслуживанию

Результаты поиска

Содержание AP610N - Aficio B/W Laser Printer

Отзывы:

Похожие инструкции для AP610N - Aficio B/W Laser Printer

Бренды по названию

Популярные бренды