Rice Lake SURVIVOR OTR Series Скачать руководство пользователя страница 24

Страница: 24 / 36

SURVIVOR OTR Flattop Truck Scale

Visit our website

www.RiceLake.com

6.3 Moist-Cure Concrete Deck

For proper curing, the surface must be kept moist for seven days. If the top surface is allowed to dry out during this time, the

finished surface is prone to spalling and surface cracking. Hot weather, full sun, and windy conditions all accelerate surface

drying.
The easiest way to keep the surface moist for seven days is to roll or spray on an epoxy-based concrete curing solution

immediately after final finishing. These epoxy-based curing products are available at contractor-supply companies.

They both seal in moisture for slow curing and protect the surface from salt and corrosion.

Some curing agents can have adverse effects on steel surfaces.
Please refer to assembly prints for proper curing agents.

Alternately, the surface can be covered with continuous plastic and kept moist by frequent flooding beneath the plastic for the

seven-day cure period.

IMPORTANT

Содержание SURVIVOR OTR Series





































Результаты поиска

Содержание SURVIVOR OTR Series

Отзывы:

Похожие инструкции для SURVIVOR OTR Series

Бренды по названию

Популярные бренды

Rice Lake SURVIVOR OTR Series, Руководство по установке

Результаты поиска

Содержание SURVIVOR OTR Series

Отзывы:

Похожие инструкции для SURVIVOR OTR Series

Бренды по названию

Популярные бренды