Rice Lake 482-AG Скачать руководство пользователя страница 21

Страница: 21 / 60

Configuration

© Rice Lake Weighing Systems

●

3.0

Configuration

The 482-AG indicator can be configured using a series of menus accessed through the indicator front panel when the indicator

is in configuration mode. To enter the configuration mode:

1. Remove setup switch access screw from back of indicator. See

Figure 2-1 on page 8

2. Using a non-conductive tool, press the button located in the access hole.

CONFIG

displays. See

Section 1.4 on

page 3

for menu navigation instructions.

The

CONFIG

menu is the first of seven main menus used to configure the indicator. Detailed descriptions of these menus are

given in this chapter. When configuration is complete, return to

CONFIG

and press the

Zero

to exit configuration mode and

save changes. Replace the configuration switch access screw.

Menu

Required

Password

Description

CONFIG Configuration Config

Graduations (scale capacity), configure zero tracking, zero range, motion band, overload, tare function, sample

rate and digital filtering parameters.

Section 3.1 on page 18

FORMAT Format

Config

Set primary and secondary units.

Section 3.1.3 on page 22

CALIBR

Calibration

Config

Calibrate the indicator.

Section 3.2 on page 23

PROGRM Program

Config

Set power-up and regulatory modes, consecutive numbering and sleep parameters.

Section 3.3 on page 24

PASWRD Password

Config

Enable and edit configuration and user passwords.

Section 3.4 on page 26

TEST

Test

Config

Test A/D, Test and set Digital I/O; reset indicator to default settings, set over and under weighment

characteristics.

Section 3.5 on page 26

User

Non Legal for Trade settings, Audit Trail, set Unit ID, set Time/Date, Communication Port,

Print Format parameters, Firmware/Software Versions.

Section 3.6 on page 27

Table 3-1. 482-AG Menu Summary

Содержание 482-AG





























































Результаты поиска

Содержание 482-AG

Отзывы:

Бренды по названию

Популярные бренды

Rice Lake 482-AG, Техническое руководство

Результаты поиска

Содержание 482-AG

Отзывы:

Бренды по названию

Популярные бренды