manualshive.com logo in svg

Rice Lake 482-AG, Техническое руководство

Поделиться
Скачать
Rice Lake 482-AG Скачать руководство пользователя страница 6

482-AG Livestock Digital Weight Indicator

2

Visit our website 

www.RiceLake.com

1.2 Overview

The 482-AG is a single-channel digital weight indicator housed in a NEMA 4X/IP66-rated stainless steel enclosure.The 

indicator front panel consists of a large (.8'', 20 mm), six-digit, seven-segment, backlight LCD display and an 18-key full numeric 

keypad.

Features

• Auto switching AC power supply 115 VAC to 230 VAC, 50-60 Hz
• Drives up to ten 350



or twenty 700



load cells

• Supports four and six wire load cell connections
• Two communications ports with Demand or Continuous (COM 2 only) outputs
• Unit ID of up to six operator entered numeric digits
• Configurable LCD backlight

Supported Application

Custom Ticket Printing: Format may be customized up to 300 characters, Time and Date, Unit ID, and Consecutive Ticket 

Number printing.

1.3 Operating Modes

The 482-AG has four modes of operation.

Weigh Mode

Weigh mode is the default mode of the indicator. The indicator displays gross weight, a transaction in process annunciator, the 

universal standstill symbol and center of zero symbol, when conditions are met, to indicate scale status (

Section 1.6 on page 4

).

Configuration Mode

Most of the procedures described in this manual, including calibration, require the indicator to be in configuration mode.
To enter the configuration mode:

1. Remove the configuration switch access screw from the back of the enclosure. See 

Figure 2-1 on page 8

.

2. Insert a non-conductive tool into the access hole and press the configuration switch. The indicator display changes to 

CONFIG

 mode.

Test Mode

Test mode provides a number of diagnostic functions for the 482-AG indicator including:

• Display raw A/D count
• Number of weighments over threshold
• Reset configuration parameters to default values

See 

Section 3.5 on page 26

 for more information on the test menu structure and the test menu functions.

Sleep Mode

Firmware version 1.03 and newer of the 482-AG

 

features a sleep mode. This feature is designed to place the indicator into a 

low power mode to reduce power consumption.
The sleep mode will activate only if the indicator is operating on the optional internal battery. If the indicator is connected to an 

external AC power source, it will not go into sleep mode regardless of the parameter settings.
The indicator will enter the sleep mode, after a specified time when no keypad activity is detected and the displayed weight is 

below the weight threshold. Setting the sleep parameter to 

NEVER

 

disables the sleep mode. A 

Standby

 

parameter determines 

how often the indicator will briefly wake, while in the sleep mode, to check for activity thresholds. See 

Section 3.3.1 on page 25

 

and 

Table 3-7 on page 24

 for information on configuring sleepmode and standby parameters

Содержание 482-AG





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды