20
TABELLA SEGNALAZIONI E ALLARMI LAMPEGGIATORE E LUCE DI CORTESIA
RISOLUZIONE PROBLEMI
Dopo aver effettuato tutti i collegamenti seguendo attentamente lo schema ed aver posizionato la basculante in posizione intermedia, verificare la corretta accensione dei led DL3, DL4.
In caso di mancata accensione dei led, sempre con basculante in posizione intermedia, verificare quanto segue e sostituire eventuali componenti guasti.
DL3
spento
Fotocellule guaste (In caso le fotocellule non siano collegate, eseguire il ponticello fra i morsetti 3 e 4)
DL4
spento
Costa guasta (In caso la costa non sia collegata, eseguire il ponticello fra i morsetti 5 e 6).
Durante il funzionamento a uomo presente, con DIP n° 8 in ON, verificare che durante l’apertura si accenda il led DL7 (verde) e che durante la chiusura si accenda il led DL6 (rosso).
In caso contrario, invertire i fili V e W del motore sui morsetti J6.
Verificare che al raggiungimento del finecorsa di apertura il led DL7 (verde) si spenga e che al raggiungimento del finecorsa di chiusura il led DL6 (rosso) si spenga, se questo non avviene
invertire i fili LSO e LSC connettore J9.
CARATTERISTICHE TECNICHE QUADRO ELETTRONICO
Range di temperatura
0÷55°C
Umidità
<95% senza condensazione
Tensione di alimentazione
230V~ ±10% (120V~ ±10% a
richiesta)
Frequenza 50/60Hz
Microinterruzioni di rete
100ms
Potenza Trasformatore
20VA - Primario 230Vac -
Secondario 11Vac e 24Vac
Carico massimo all’uscita del lampeggiatore
20W a 24Vdc con carico
resistivo
Assorbimento massimo scheda (esclusi accessori)
45mA
Corrente disponibile per accessori
0,5 A +/-15% 24Vac
CARATTERISTICHE TECNICHE RADIO (solo modelli CRX)
Frequenza Ricezione
433,92MHz
Impedenza 52
Sensibilità >2,24μV
Tempo eccitazione
300ms
Tempo diseccitazione
300ms
Codici memorizzabili
N° 64 per comando basculante e
N° 64 per comando luce di cortesia
Corrente disponibile su connettore radio
200mA 24Vac
- Tutti gli ingressi devono essere utilizzati come contatti puliti perchè l’alimentazione è generata internamente alla scheda ed è disposta in modo da garantire il rispetto di isolamento doppio
o rinforzato rispetto alle parti in tensione.
- Tutti gli ingressi vengono gestiti da un circuito integrato programmato che esegue un autocontrollo ad ogni avvio di marcia.
I
DIFETTO
SOLUZIONE
Dopo aver effettuato i vari collegamenti e aver dato tensione, tutti i led sono spenti.
Verificare la presenza della tensione di alimentazione ai morsetti L-N.
Verificare l’integrità dei fusibili F1 e F2. In caso di fusibile interrotto usarne solo di valore
adeguato F1 = T 5 A F2 = T 0,1A
La basculante ha un movimento irregolare, a onde.
Bilanciare correttamente la basculante in modo che il suo movimento manuale si possa
effettuare con la stessa identica forza sia in apertura che in chiusura.
La basculante al raggiungimento della totale apertura o chiusura inverte il movimento.
Eseguire la regolazione dei finecorsa elettrici.
La manovra di sblocco manuale è molto rumorosa.
Eseguire una regolazione accurata dei finecorsa elettrici.
La basculante inverte il moto in assenza di eventi durante la corsa.
Aumentare la forza del motore tramite il trimmer TORQUE.
La basculante esegue l’apertura, ma non chiude dopo il tempo impostato.
Accertarsi che il led DL9 sia acceso.
Pulsante K sempre inserito in modalità di funzionamento automatico (DIP 1 OFF).
Sostituire pulsante o switch del selettore.
Autotest costa fallito => verificare i collegamenti tra quadro elettronico e alimentatore per
coste.
Attenzione
: se non si sta utilizzando un alimentatore per coste il DIP 6 deve essere in
posizione OFF.
La basculante non apre e non chiude azionando i vari pulsanti K - K COVER o RADIO.
Contatto costa sicurezza guasto.
Contatto fotocellule guasto con DIP 2 OFF.
Sistemare o sostituire il relativo contatto.
Il microinterruttore della porta pedonale è aperto. Sostituirlo verificando poi che il led DL3
sia acceso.
Il motore gira ma la basculante non si muove e dopo 40 secondi si ferma con luce di
cortesia che lampeggia.
Riagganciare lo sblocco manuale e poi dare un comando.
EVENTO
CAUSA
SEGNALAZIONE DA LUCE
DI CORTESIA
SEGNALAZIONE DA
LAMPEGGIATORE
Allarme encoder guasto.
Guasto, filo staccato o sblocco manuale
azionato.
2 sec. ON e 400 ms OFF sempre.
Accesa per 1 minuto.
Allarme encoder sicurezza.
Doppio impatto in un ciclo di funzionamento
300 ms ON e 2 sec. OFF sempre.
Accesa per 1 minuto.
Allarme costa.
Doppio impatto in un ciclo di
funzionamento.
300 ms ON e 2 sec. OFF sempre.
Accesa per 1 minuto.
Allarme autotest costa.
Autotest fallito a fine apertura.
300 ms ON e 2 sec. OFF sempre.
Accesa sempre.
Allarme da finecorsa non premuto e
raggiungimento over corrente sia in apertura
che in chiusura.
Finecorsa di apertura o di chiusura non
correttamente tarato.
280 ms ON 2000 ms OFF sempre.
Spenta.
Allarme di sicurezza fotocellula o costa
impegnata.
Fotocellula o costa impegnata a fronte di un
comando.
100 ms ON e 200 ms OFF attiva per 20
secondi.
Spenta.
Memoria codici radio satura.
Memoria piena.
Emette 6 lampeggi.
Spenta.
Содержание BOSS 230V MASTER DX
Страница 14: ...14 64 65 66 67 68 69 70 71 72 73 74 I ...
Страница 32: ...32 F 64 65 66 67 68 69 70 71 72 73 74 ...
Страница 50: ...50 G B 64 65 66 67 68 69 70 71 72 73 74 ...
Страница 58: ...NOTES 58 ...