background image

TO WATCH VIDEOS GO TO: 

tinyurl.com/lgh5x3h

 

Contents

Preparation ......................................2-5
Assembly .......................................6-10
Installation ..................................11-28
  Install the Door Control ............21-22
  Install the Protector System® ....23-26
 Connect 

Power 

.........................27-28

Adjustments .................................29-31
Operation .....................................32-35
 Features 

.......................................33

  Using your Garage Door Opener .....34
  Push Button Door Control ..............34
   Remote Control and

Keyless Entry ................................35

 Homelink® 

...................................35

  To Erase the Memory .....................35
  To Open the Door Manually ...........36
Maintenance .....................................37
Troubleshooting ...........................38-39
Accessories ........................................40
Warranty ...........................................41
Repair Parts .................................42-43

Owner’s Manual

C205

Chain Drive 

Garage Door Opener

FOR RESIDENTIAL USE ONLY

PRE-PROGRAMMED REMOTE CONTROL 

INCLUDED

www.chamberlain.com

www.mychamberlain.com

•  Please read this manual and the enclosed safety materials carefully!
•  Fasten the manual near the garage door after installation.
•  The door WILL NOT CLOSE unless the Protector System

®

 is connected 

and properly aligned.

•  Periodic checks of the garage door opener are required to ensure 

safe operation.

•  The model number label is located on the front panel of your garage 

door opener.

• This garage door opener is compatible with MyQ® and 

S

b

2.0® accessories.

•  DO NOT install on a one-piece door if using devices or features 

providing unattended close. Unattended devices and features are 

to be used ONLY with sectional doors.

Garage Opener

Summary of Contents for C205

























































































Reviews: