13
Func.
Name
Description
Range of
Setting
Unit Default
F_112
Communication
Protocol
0: 8,N,2 1: 8,E,1
2: 8,O,1 3: 8,N,1
0~3
─
1
F_113
Communication
Overtime (Cot)
When the message transmission is interrupted or
delays during communication transmission, drive
displays “Cot” message. (0.0: disable)
0.0~
100.0
0.1
sec
0.0
F_114
Communication
Overtime Disposal
0: Warning (Cot)
；
Continue operation
1: Warning (Cot)
；
Ramp to stop
2: Warning (Cot)
；
Coast to stop
0~2
─
0
F_115
Control Selection of
Multi-Function
Input Terminals
0: Multi-function input terminals (X1~X6) selves
1: Multi-function input terminals (X1~X6) command
by communication interface
0,1
─
0
F_116
Fault Reset
Selection
0: Auto-restart immediately (OC,OE,GF only).
1: Auto reset from 0Hz after the setting time (F_117).
2: Auto reset from 0Hz after the setting time (F_117)
without executing error detection. (If the drive runs
over 24hrs without any error, the drive will reset
the counting number)
0~2
─
0
F_117
Error Tripping Time
Interval before
Auto-Restart
Set the error tripping time interval before drive auto
restarts when the drive trips to stop.
(F_116=2 or 3)
1~200
10sec
6
F_118
UP/DOWN
Memory Selection
0: Clear the UP/DOWN frequency command when
power failure.
1: Save the UP/DOWN frequency command at F_121
when power failure.
0, 1
─
0
F_119
UP/DOWN
Frequency
Resolution
0: 0.01Hz 1~8: x0.05Hz
9: 0.5Hz 10~250: x0.1Hz
0~250
─
0
F_120
UP/DOWN
Trigger Mode
1~5: Continuous accel./decel. when the terminal is
activated with the duration (1 ~ 5 sec).
6: Edge trigger
1~6
─
1
F_121
UP/DOWN
Frequency
Adjustment
Adjust UP/DOWN frequency by KP-603 keypad.
0.00~
400.00
0.01
Hz
0.00
F_122
Secondary
Frequency
Command Selection
0: Frequency command by analog signal via terminal.
1: Frequency command by keypad.
2: Frequency command by UP/DOWN terminal.
3: Frequency command by communication.
0~3
─
0
F_123
Analog Input
Selection
0: Vin+Iin
1: Vin-Iin
2: Iin-Vin
3: Vin or Iin(switch by multi-function input terminal).
0~3
─
0
F_124
Analog Input
Selection
(Vin)
0: Analog input gain
1: Frequency command
2: Current limit level
3: Adjust output voltage of V/F pattern
4: Feedback signal
0~4
─
1
F_125
Analog Input
Selection
(Iin)
0: Analog input gain
1: Frequency command
2: Current limit level
3: Adjust output voltage of V/F pattern
4: Feedback sugnal
0~4
─
1
F_126 Iin Range Selection 0: 4~20mA (2~10V) 1: 0~20mA (0~10V)
0,1
─
0
F_127
Gain(Iin)
The gain ratio of analog input terminal Iin.
0.00~2.00 0.01
1.00
F_128
Bias(Iin)
The bias ratio of analog input terminal Iin.
-1.00~
1.00
0.01
0.00
F_129
Analog Output
Signal Selection
(AM+)
0:Output frequency
2:Output current
4:Iin frequency command
6:Output voltage
1:Frequency command.
3:Vin frequency command
5:DC bus voltage
7:Heat sink temperature
0~7
─
2
F_130
Gain (AM+)
AM+ analog output adjustment ratio.
0.00~2.00 0.01
1.00
F_131
Multi-function
Output Terminal
(Ta2/Tc2)
The way of settings are same as multi-function output
terminals setting.(F_058 ~ F_060)
-16~+16
(Note 7)
─
1
F_132
DC Braking
Frequencyat Stop Active frequency level of DC braking at stop.
0.1~60.0 0.1Hz
0.5
F_135 200% Current limit 0: Disable 1: Enable
0,1
─
0
