Rheem Raypak 2450 Скачать руководство пользователя страница 24

Страница: 24 / 54

Item

Range

Default

Value

Access

Level

Description

AUX1 On Time

12:00A-11:59P

Installer/

Service

Sub-

Select ON time for AUX1 to take effect.

AUX1 Off Time

12:00A-11:59P

Installer/

Service

Sub-

Select OFF time for AUX1 to stop.

AUX2 On Time

12:00A-11:59P

Installer/

Service

Sub-

Select ON time for AUX2 to take effect.

AUX2 Off Time

12:00A-11:59P

Installer/

Service

Sub-

Select OFF time for AUX2 to stop.

Defrost Temp

20°F–35°F

(-6.5°C–1.5°C)

35°F

(1.5°C)

Installer/

Service

Sub-

This is the temperature measured on the coil

when the control goes into Defrost mode.

Def Terminate

40°F–60°F

( 4°C–15.5vC)

50°F

(10°C)

Installer/

Service

Sub-

If the coil temperature reaches this setpoint,

Defrost will terminate. Other Defrost

algorithms are still operating behinds the

scene.

Outside Lockout

Off,

30°F–50°F

(-1°C–10°C)

Off

Installer/

Service

Sub-

The installer can program the control to Lock

out operation of the unit if a specific outside

temperature is measured. Off allows operation

at any ambient temperature.

Set Model Type

HEAT ONLY,

POWER DEFROST,

HEAT/COOL

HEAT/

COOL

Installer/

Service

Sub-

Set at the factory. Will need to be set by

Installer during any replacement of the control

board.

EXV

Disabled, Type 1,

Type 2

Disabled

Installer/

Service

Sub-

Set at the factory on new units. Select

“Disabled” if unit equipped with TXV for board

replacement. EXV Type 1 is 500 step EXV.

EXV Type 2 is 1600 step EXV.

Change EXV to

Yes/No

Installer/

Service

Sub-

This screen asks if you really want to change

the EXV setting – the UP or DOWN button

must be pressed to show YES before the EXV

type will be changed.

Brownout

Detection On

On/Off

Installer/

Service

Sub-

This function will shut down operation of the

unit if the 24VAC signal drops below 18VAC to

protect the unit from Low Voltage. This feature

can be turned off as desired.

Set Factory

Defaults

Installer/

Service

Sub-

Press and hold both the UP and DOWN

buttons for 3+ seconds to reset the factory

defaults in the control. When reset, the screen

will display “Defaults Set”.

Содержание Raypak 2450























































Результаты поиска

Содержание Raypak 2450

Отзывы:

Похожие инструкции для Raypak 2450

Бренды по названию

Популярные бренды

Rheem Raypak 2450, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Raypak 2450

Отзывы:

Похожие инструкции для Raypak 2450

Бренды по названию

Популярные бренды