manualshive.com logo in svg

Rheem 874W27NF, Руководство по обслуживанию, Страница: 60 / 61

Поделиться
Скачать
Rheem 874W27NF Скачать руководство пользователя страница 60

60 

TM061 Rheem 27 Water Star Service Instructions 

– Issued: 11/10 

REV A Issued 08/13 
 

This document is stored and maintained electronically by 

  Service. Al

l printed copies not bearing this statement in RED are deemed “uncontrolled”

 

Thermostat (Procedure 31) 

 

1. 

Switch off power at GPO and unplug power cord from GPO.   

2.  Remove the front cover (Refer to procedure 1). 

3.  Disconnect the drain line from the T&PR valve by removing the two quick connect clips 

that  retain  the  T&PR  drain  line.  Gently  pull  the  drain  line  clear  of  the  T&PR  valve  to 
disengage. 

4.  Disconnect the multi-pin connector (blue and brown wires) of the incoming power supply. 

5.  Disconnect the earth wire from the earth nest at bottom left hand side of heater cabinet 

6.  Undo the packing straps and remove the front polystyrene insulation to expose the hot 

water storage tank. 

7.  Disconnect the red element wires from terminals 2 & 4 of the thermostat. 

8.  Disconnect the blue and brown wires from terminals 1 & 3 of the thermostat.

 

9.  Slide thermostat out from under thermostat bracket. 

 

10. Reassemble in the reverse order of above. 

 

 

 

Hot Water Storage Tank Replacement (Procedure 32)

 

 
 

 

1. 

Switch  off  power  at  GPO,  unplug  power  cord  from  GPO  and  isolate  the  water 
supply to the water heater. 

2.  Remove  the  front  cover,  hot  water  storage  tank,  transfer  valve,  hot  water  outlet  tee, 

T&PR valve, element, and thermostat. Refer to procedures 1, 26, 27, 28, 29, 30 & 31.

 

3.  Remove hot water storage tank from rear insulation and replace. 

4.  Reassemble in reverse order of above. 

5.  Check for water leaks.

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание 874W27NF






























































Отзывы:

Нет отзывов