manualshive.com logo in svg

Rheem 874W27NF, Руководство по обслуживанию, Страница: 56 / 61

Поделиться
Скачать
Rheem 874W27NF Скачать руководство пользователя страница 56

56 

TM061 Rheem 27 Water Star Service Instructions 

– Issued: 11/10 

REV A Issued 08/13 
 

This document is stored and maintained electronically by 

  Service. Al

l printed copies not bearing this statement in RED are deemed “uncontrolled”

 

6.  Remove the  three  screws retaining the heat exchanger.  Two from the top of the heat 

exchanger to the side of the flue outlet and one from the bottom of combustion chamber 
to the right of fan housing.   

7.  Remove heat exchanger by gently lifting the assembly up and clear of heater cabinet. 

8.  Some wiring retainers will need to be released to enable removal of wiring.   

9.  Reassemble in reverse order of above.   

10. Test for gas leaks using soapy water solution 

11. Check for water leaks. 

 
Heat Exchanger Replacement (Procedure 22) 

 

 

1. 

Isolate power and water supplies.

 

2.  Remove heat exchanger. Refer to procedure 21. 

3.  Remove  the  burner  assembly,  anti-frost heaters,  fan  assembly  and  cowling  assembly 

from the old heat exchanger and refit to the replacement heat exchanger.   

4.  Check the overheat limiter. Replace if damaged or open circuit. 

5.  Reassemble in reverse order of above.   

6.  Test for gas leaks using soapy water solution 

7.  Check for water leaks. 

 
Over Heat Limiter Assembly: (Procedure 23) 

 

Replacement of the overheat limiter requires removal and possible replacement of the heat 
exchanger. 

 

1.  Remove heat exchanger. Refer to procedure 21. 

2.  Inspect the heat exchanger for holes or combustion damage. (Replace heat exchanger if 

necessary) 

3.  Remove the two white wires from the terminal block on the right hand side of overheat 

limiter assembly. 

4.  Remove  the  two  plastic  rivets  retaining  the  overheat  limiter  assembly  to  the  back  of 

heater cabinet and remove the overheat limiter assembly. 

5.  Reassemble in reverse order of above (Note: Ensure all multi-pin plugs are reconnected 

and all wiring is neatly repositioned and retained to prevent damage during operation). 

 

Ignition Pack Replacement: (Procedure 24) 

 

1. 

Isolate power supply.

 

2.  Remove  the  front  cover,  burner  cover  plate,  gas  manifold  assembly  and  burner 

assembly. Refer to procedures 1, 5, 6 and 7.   

3.  Disconnect black high voltage lead from ignition electrode on right hand side of burner 

assembly. 

4.  Replace ignition pack. 

5.  Reassemble  in  reverse  order  of  above.  NOTE:  Ensure  wiring  to  igniter  and  flame 

sensors is not pinched during reassembly. 

 

Содержание 874W27NF






























































Отзывы:

Нет отзывов