manualshive.com logo in svg

Rheem 874W27NF, Руководство по обслуживанию, Страница: 57 / 61

Поделиться
Скачать
Rheem 874W27NF Скачать руководство пользователя страница 57

57 

TM061 Rheem 27 Water Star Service Instructions 

– Issued: 11/10 

REV A Issued 08/13 
 

This document is stored and maintained electronically by 

  Service. Al

l printed copies not bearing this statement in RED are deemed “uncontrolled”

 

Transformer: (Procedure 25) 

 

1. 

Isolate power supply.

 

2.  Remove the front cover, LED display, control PCB, power supply PCB and PGFR. Refer 

to procedures 1, 2, 3, 4 and 10. 

3.  Disconnect  primary  transformer  windings  (blue  &  brown  wires)  from  middle  of  power 

supply PCB (Terminal C). 

4.  Disconnect  the  secondary  windings  from  the  top  left  hand  side  of  power  supply  PCB 

(Terminal E). 

5.  Remove the four screws retaining the transformer to the back of the water heater cabinet. 

6.  Lift the transformer out of heater cabinet. 

7.  Reassemble in reverse order of above. 
 

 

Hot Water Storage Tank Removal (Procedure 26)

 

 
 

1. 

Switch off power at GPO and unplug power cord from GPO.   

2.  Remove the front cover. Refer to procedure 1.

 

3.  Reduce the temperature of the water stored in the hot water storage tank by opening a 

hot tap or the T&PR relief for approx 30 seconds until water runs cold.

 

4.  Isolate the water supply to the water heater. 

5.  Relieve pressure from the water heater by easing the T&PR valve. Leave valve open. 

6.  Disconnect the transfer pipe from the inlet of the hot water storage tank. At this point the 

contents of the 2.6L hot water storage tank will be relieved through this inlet fitting. 

7.  Disconnect the hot water outlet pipe. 

8.  Disconnect the T&PR relief valve drain line from the underside of the heater cabinet. 

9.  Remove the quick connect clip from the T&PR drain line where the drain line exits the 

heater cabinet. 

10. Remove the 2 screws from the underside of the heater cabinet that retain the T&PR relief 

drain connection.             

11. Remove the 2 screws from the underside of the heater cabinet that retain the hot water 

outlet connection. 

12. Remove  the  2  screws  from  the  underside  of  the  heater  cabinet  that  retain  the  inlet 

connection to the hot water storage tank. 

13. Disconnect the multi-pin connector (blue and brown wires) of the incoming power supply.   

14. Disconnect the earth wire from the earth nest at bottom left hand side of heater cabinet.     

15. Remove the small piece of insulation situated above the hot water storage tank. 

16. Lift complete storage tank assembly up and then slide forward to lift clear of the heater 

cabinet. 

 

17. Reassemble  in  reverse  order  of  above.  Ensure  water  supply  is  turned  on  and  all  air 

purged from the unit before energising unit to ensure no damage occurs to the heating 
element or heat exchanger. 

 

Содержание 874W27NF






























































Отзывы:

Нет отзывов