manualshive.com logo in svg

Rheem 874W27NF, Руководство по обслуживанию, Страница: 59 / 61

Поделиться
Скачать
Rheem 874W27NF Скачать руководство пользователя страница 59

59 

TM061 Rheem 27 Water Star Service Instructions 

– Issued: 11/10 

REV A Issued 08/13 
 

This document is stored and maintained electronically by 

  Service. Al

l printed copies not bearing this statement in RED are deemed “uncontrolled”

 

Temperature and Pressure Relief Valve (Procedure 29) 

 

Never  fit a  T&PR valve  with  a  rating  higher  than  that  indicated  on  the  water 
heater rating plate. Do not use reconditioned T&PR valves.

 

 

1. 

Switch  off  power  at  GPO,  unplug  power  cord  from  GPO  and  isolate  the  water 
supply to the water heater. 

2.  Remove the front cover (Refer to procedure 1). 

3.  Relieve pressure from the water heater by easing the T&PR valve. Keep valve open until 

water ceases to flow from drain pipe.   

4.  Disconnect the drain line from the T&PR valve by removing the two quick connect clips 

that  retain  the  T&PR  drain  line.  Gently  pull  the  drain  line  clear  of  the  T&PR  valve  to 
disengage. 

5.  Disconnect the multi-pin connector (blue and brown wires) of the incoming power supply. 

6.  Disconnect the earth wire from the earth nest at bottom left hand side of heater cabinet 

7.  Undo the packing straps and remove the front polystyrene insulation to expose the hot 

water storage tank. 

8.  Remove the 

½” brass quick connect fitting from the outlet of the T&PR valve. 

9.  Unscrew the T&PR valve from the top of the cylinder.

 

10. Confirm the replacement T&PR valve is the correct rating and refit using thread tape.

 

11. Reassemble in the reverse order of above. 

 

12. Restore the water supply.

 

13. Check the T&PR valve thread and connections for leaks.

 

 

 

Element (Procedure 30) 

 

 

1. 

Switch  off  power  at  GPO,  unplug  power  cord  from  GPO  and  isolate  the  water 
supply to the water heater. 

2.  Remove the front cover (Refer to procedure 1). 

3.  Relieve pressure from the water heater by easing the T&PR valve. Keep valve open until 

water ceases to flow from drain pipe.   

4.  Disconnect the drain line from the T&PR valve by removing the two quick connect clips 

that  retain  the  T&PR  drain  line.  Gently  pull  the  drain  line  clear  of  the  T&PR  valve  to 
disengage. 

5.  Disconnect the multi-pin connector (blue and brown wires) of the incoming power supply. 

6.  Disconnect the earth wire from the earth nest at bottom left hand side of heater cabinet 

7.  Undo the packing straps and remove the front polystyrene insulation to expose the hot 

water storage tank. 

8.  Undo the red element wires from the terminals 2 & 4 of the thermostat. 

9.  Unscrew the element from the hot water storage tank.

 

10. Confirm the replacement element is the correct rating and refit.

 

11. Reassemble in the reverse order of above. 

 

12. Check the element connections for leaks.

 

 

Содержание 874W27NF






























































Отзывы:

Нет отзывов