manualshive.com logo in svg

Rheem 874W27NF, Руководство по обслуживанию, Страница: 51 / 61

Поделиться
Скачать
Rheem 874W27NF Скачать руководство пользователя страница 51

51 

TM061 Rheem 27 Water Star Service Instructions 

– Issued: 11/10 

REV A Issued 08/13 
 

This document is stored and maintained electronically by 

  Service. Al

l printed copies not bearing this statement in RED are deemed “uncontrolled”

 

Flame Sensor: (Procedure 8) 

 

1. 

Isolate power and gas supplies.

   

2.  Remove  the  front  cover,  burner  cover  plate  and  gas  manifold  assembly.  Refer  to 

procedures 1, 5, and 6.   

3.  Remove the protective silicon tube from flame sensor mounted on the front left hand side 

of burner assembly. 

4.  Remove retaining screw from flame sensor holder and remove flame sensor. 

4.  Reassemble in reverse order of above. 

NOTE:

 Ensure wiring to igniter and flame sensor 

is not pinched during reassembly. Ensure the three gaskets on gas valve assembly are 
intact and correctly fitted.   

5.  Test for gas leaks with soapy water solution. 

 
Power cord: (Procedure 9)

 

 

1.  Isolate power and unplug power cord from power point. 

2.  Remove the front panel. Refer to procedure 1. 

3.  Undo cord clamp screw located on bottom left hand side of PCB and remove clamp. 

4.  Disconnect Earth connection at PCB housing. 

5.  Disconnect the power cable wiring loom plug and withdraw power cable through slot in 

heater jacket. 

6.  Reassemble in reverse order of above. 

 
Proportional Gas Flow Regulating Valve: (Procedure 10) 

 

1. 

Isolate power and gas supplies.

 

2.  Remove  the  front  cover,  OK  monitor  and  plate,  burner  cover  plate  and  gas  manifold 

assembly. Refer to procedures 1, 4, 5, and 6.   

3.  Disconnect the gas supply pipe from the gas inlet connection. 

4.  Remove  the  three  silver  screws  from  the  gas  inlet  connector  on  the  underside  of  the 

heater cabinet. Gently pull the gas inlet connector to remove.     

5.  Carefully  remove  the  proportional  gas  flow  regulating  valve  (PGFR)  from  the  water 

heater. 

6.  Disconnect  the  multi-pin  wiring  plugs  from  the  gas  inlet  solenoid  valve  (GISV),  the 

proportional gas flow regulating valve (PGFR) and solenoid valves 1, 2 & 3. 

7.  Reassemble in reverse order of above. Ensure the three gaskets on gas valve assembly 

are intact and correctly fitted (replace gaskets if required). 

8.  Test for gas leaks with soapy water solution. 
 

 

Содержание 874W27NF






























































Отзывы:

Нет отзывов