Rheem 18 Скачать руководство пользователя страница 35

Страница: 35 / 80

TEMPERATURE CONTROL – DELUXE

Turning Off Bath Fill Mode During Its Operation

The bath fill operation can be interrupted by pressing the BATH FILL button before completion of the bath fill
operation.

If it is necessary to turn off the Bath Fill mode before the operation is complete, during

Step

Press the BATH FILL button

At this first press of the BATH FILL button



Water flow from the hot tap will cease



The operating light will go out



The bath fill water volume display panel will show
0 litres.



The temperature display will go blank



The bath fill operating light will flash



The voice prompt will sound

“bath filling has been stopped, please turn off the hot
water tap and press the BATH FILL button to finish”

Close the hot tap

Press the BATH FILL button again

At this second press of the BATH FILL button



The bath fill operating light and bath fill indicator light
will go out



The bath fill water volume display will go blank



Note:

If the hot tap has not been turned off, the

voice prompt will sound

“please ensure the bath hot water tap is turned off”

“bath filling has been stopped,

please turn off the hot water tap

and press the

BATH

FILL button to finish”

BATH FILL

BATH

(

)

4 0

°C

ACTIVE

ON/OFF

BATH FILL

BATH

(

)

4 0

°C

ACTIVE

ON/OFF

“please ensure the bath hot

water tap is turne

d off”

BATH

(

)

4 0

°C

ACTIVE

ON/OFF

BATH FILL

Содержание 18

















































































Результаты поиска

Содержание 18

Отзывы:

Похожие инструкции для 18

Бренды по названию

Популярные бренды

Rheem 18, Руководство пользователя и инструкции по установке

Результаты поиска

Содержание 18

Отзывы:

Похожие инструкции для 18

Бренды по названию

Популярные бренды