Rheem 18 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 80

background image

58

EZ-LINK SYSTEM DUAL INSTALLATION

The EZ-

Link™ system is designed to electronically control two continuous flow gas water heaters and have

them operate as one. One or both water heaters may be in operation, depending upon the hot water
demand. The second water heater will only operate when the hot water demand exceeds the capacity of the
first water heater to supply.

The EZ-Link system is suitable for installation with Rheem 874 and 876 series 018 and 020 models
continuous flow gas water heaters. The Ez-Link Kit PN 290141 is required for the installation.

EZ-LINK KIT (290141)

Warning Label x 1 (121109)
AGA Label x 1 (121901)

+ Installation Instruction x 1 (122139)

DO NOT

OPERATE THIS APPLIANCE BEFORE
READING THE INSTRUCTION

BOOKLET.

DO NOT

PLACE ARTICLES ON OR AGAINST
THIS APPLIANCE.

DO NOT

STORE CHEMICALS OR FLAMMABLE
MATERIALS, OR SPRAY AEROSOLS
NEAR THIS APPLIANCE.

DO NOT

OPERATE WITH PANELS, COVERS

OR GUARDS REMOVED FROM THIS
APPLIANCE.

DO NOT

ENCLOSE THIS APPLANCE.

CERTIFIED FOR OUTDOOR INSTALLATION ONLY

To operate the water heater

Open the inlet water and gas valves fully

Plug appliance into mains power outlet and switch on

Turn on remote temperature controller(s) if fitted
Open a hot tap - the heater will operate automatically

To shut down the water heater

Close the inlet water and gas valves fully

Turn off remote temperature controller(s) if fitted

If power will be disconnected, refer to the owners guide

regarding draining the appliance to avoid damage due to
freezing

121109 AD

N199

AS 3498
WMKA21434

Ez-Link Cable x 1

Cable Clamp x 2
Screw x 2

Ez-Link Kit

–

PN 290141

Notes:

Only two continuous flow gas water heaters can be installed with an Ez-Link system.

The two continuous flow water heaters must be of the same model. The performance of two different
model water heaters manifolded together cannot be guaranteed.

A temperature controller is required to be installed with the EZ-Link system. The controller can be either
a standard or Deluxe controller.

Two continuous flow water heaters manifolded together with an Ez-Link system installed cannot be used
as an in-series gas booster system to a solar water heater installation. Temperature controllers

must not

be fitted to a water heater as part of a solar water heater system because water at a

temperature much higher than the controller setting can be delivered.

screws x 2

cable clamps

x 2

Ez-Link cable x 1

warning label x 1

(121109)

AGA label x 1

(121901)

«
...
56
57
58
59
60
...
»

Содержание 18

















































































Отзывы:

Нет отзывов

Похожие инструкции для 18

Бренд: L.B. White Страницы: 28

Бренд: GE Страницы: 28

Бренд: Zehnder Pumpen Страницы: 24

FCD-JTHMG80-III

Бренд: Haier Страницы: 2

Little Sea-ox FCD-JTHC40-III (E)

Бренд: Haier Страницы: 6

Бренд: Haier Страницы: 18

Бренд: Haier Страницы: 23

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 2

Бренд: A.O. Smith Страницы: 77

WILDEN P100 Advanced Plastic

Бренд: PSG Dover Страницы: 28

Бренд: REMKO Страницы: 20

Taro HCS SJ Series

Бренд: Texmo Industries Страницы: 41

Бренд: Orbegozo Страницы: 85

Бренд: QualityCraft Страницы: 5

Бренд: Thermal Technology Страницы: 24

Бренд: Oase Страницы: 16

Бренд: Grundfos Страницы: 153

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды