Rheem 18 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 80

background image

39

SAVE A SERVICE CALL

Check the items below before making a service call. You will be charged for attending to any condition or
fault, which is not related to manufacture or failure of a part (refer to

“Warranty”

on page 80).

NO DISPLAY ON THE CONTROLLER

Is the controller turned on?

Press the on / off button (refer to

“Temperature Control”

on pages 9 to 38).

Is the water heater plugged in and the power outlet switched on?

Is power available in the house?

Try using another electrical appliance.

COLD WATER FROM THE HOT TAP

Is the controller turned on?

Press the on / off button (refer to

“Temperature Control”

on

pages 9 to 38).

Close the hot tap, wait 10 seconds and open the hot tap again.

Is the hot tap open enough?

The burners will not light if the flow rate is less than 2.5 L / min.

Is the water heater plugged in and the power outlet switched on?

Is power available in the house?

Try using another electrical appliance.

Is the isolation valve in the gas line open?

Is there a gas supply to the rest of the house?

Try lighting another gas appliance.

Has the gas line been purged of air after installation?

Refer to your plumber.

WATER IS TOO HOT OR NOT HOT ENOUGH

Does the controller you are using have priority? (refer to

“Temperature Control”

on pages 9 to 38)

Note:

For an 876 series water heater, 48 C is the maximum available temperature.

NO WATER FROM THE HOT TAP

No flow of water from the hot tap may indicate a restriction in or failure of the cold water supply to the water
heater. Check for water flow at other taps and that the cold water isolation valve

(refer to page

55

)

is fully

open.

WATER FLOW FLUCTUATES

More than one or two hot taps in use at the same time may cause a decrease in the hot water flow from the
taps. This can also be evident if the water heater has been installed as a gas booster water heater to a solar
preheat water heater and the solar preheat water is at a low temperature.

Are there more than one or two hot taps open, or are appliances such as a dishwasher or washing
machine, in use at the same time?

Ensure only one or two hot taps (or appliance) are on at the one time.

Check the flow of the water from one tap, eg, the shower.

The shower should be adjusted so the hot tap is fully open.

«
...
37
38
39
40
41
...
»

Содержание 18

















































































Отзывы:

Нет отзывов

Похожие инструкции для 18

Бренд: iGenix Страницы: 6

Бренд: Kambrook Страницы: 6

Бренд: BLACKMER Страницы: 12

Бренд: S&P Страницы: 24

Бренд: Lancaster Water Treatment Страницы: 14

Бренд: Honda Страницы: 75

Бренд: Far Group Страницы: 12

MegaLife HE Series

Бренд: Heatrae Sadia Страницы: 24

Бренд: Varian Страницы: 24

XC Filter Cartridge EV9613-09

Бренд: Everpure Страницы: 2

Ama-Drainer 4 Series

Бренд: KSB Страницы: 60

Бренд: Barnstead Thermolyne Corporation Страницы: 32

Warren Rupp SANDPIPER Beast SPB20

Бренд: Idex Страницы: 21

TUNSTALL Double

Бренд: Eastbrook Страницы: 4

Бренд: Jaga Страницы: 12

Бренд: Raypak Страницы: 32

Бренд: Dantherm Страницы: 135

Water Heater 520 Direct Vent Indoor

Бренд: A.O. Smith Страницы: 97

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды