Rheem 18 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 80

background image

55

CONNECTIONS – PLUMBING

CONNECTION SIZES

Model

018 to 020

Hot water connection

R¾/20

Cold water connection

R¾/20

Gas inlet

R¾/20

All plumbing work must be carried out by a qualified person and in accordance with the National Plumbing
Standard AS/NZS 3500.4 and local authority requirements.

All gas work must be carried out by a qualified person and in accordance with the Australian Gas
Installations Standard AS 5601 and local authority requirements.

WATER INLET AND OUTLET

All  pipe  work  must  be  cleared  of  foreign  matter  before
connection  and  purged  before  attempting  to  operate  the
water heater. All olive compression fittings must use brass
or  copper  olives.  Use  thread  sealing  tape  or  approved
thread sealant on all fittings.

A full flow gate valve or ball valve must be installed on the
cold  water  line  or  solar  preheat  water  line  to  the  water
heater.

A non return valve or stop tap must not be

installed.

An acceptable arrangement is shown in the

diagram. Refer also to

“Hot Water Delivery”

on page 45

and to

“Mains Water Supply”

on page 44.

A disconnection union must always be provided at the cold
water inlet and hot water outlet on the water heater to
allow for disconnection of the water heater.

Insulation used on the cold and hot water lines must
extend up to the cold water inlet and hot water outlet of the
water heater.

Notes:

It is essential all pipe connections be correctly aligned,
otherwise  component  connections  within  the  water
heater  may  be  strained  and / or  components
themselves  misaligned.  It  is  recommended  also,
wherever  possible,  pipe  connections  be  made  at  the
water  heater  first  and  final  pipe  runs  be  made  in  soft
copper

pipe

to

allow

some

adjustment

for

misalignment.

Use the spanner flats on the water heater fittings and
take care to avoid twisting the water inlet and outlet
pipes inside the jacket.

Gas booster 874 series water heaters

do not

need to

be installed with a solar bypass valve.

The maximum supply temperature to the water heater
when used as an in-series gas booster for a solar
preheat water heater is 80°C.

HOT

WATER

POWER

CORD

PRESSURE

LIMITING

VALVE

GATE VALVE

OR

BALL VALVE

GAS

COCK

WATER AND GAS CONNECTION DETAIL

SK6327 A4
07/08 REV-BD

COLD

WATER

GAS

Gas Water Heater

Cold and Hot Water Connection Details

SOLAR PREHEAT WATER & GAS CONNECTION DETAIL

HOT

WATER

POWER

CORD

GATE VALVE

OR

BALL VALVE

GAS

COCK

SOLAR

PREHEAT

WATER

GAS

Gas Booster for a Solar Preheater

Solar Preheat and Hot Water Connection Details

«
...
53
54
55
56
57
...
»

Содержание 18

















































































Отзывы:

Нет отзывов

Похожие инструкции для 18

Little Sea-ox FCD-30

Бренд: Haier Страницы: 23

SmartWater GNSF35Z

Бренд: GE Страницы: 3

Бренд: GE Страницы: 64

Бренд: GE Страницы: 36

Бренд: B-TEC Страницы: 11

Бренд: Bacharach Страницы: 12

Бренд: Eastern Tabletop Страницы: 19

Бренд: Jandy Страницы: 52

Water Solutions 3098 Series

Бренд: Zoeller Страницы: 4

Aquanot Spin 508

Бренд: Zoeller Страницы: 2

Бренд: Zoeller Страницы: 11

Бренд: Zip Страницы: 18

Бренд: Paloma Страницы: 28

Xsential QUAD-RO

Бренд: Watermark Страницы: 8

Бренд: ICON Страницы: 16

Comfort Glow CGR2N

Бренд: Desa Страницы: 20

Waterfall Kit WFK8

Бренд: Beckett Страницы: 1

Goulds CentriPro M05411

Бренд: Xylem Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды