background image

 

Ethernet (LAN) 

 RF In and RF Out - Cables  

 

LAN and RF (coax) Cables are not supplied.   
 
Cat5 LAN cable is sufficient to connect the Antenna Controller to your router or switch. 
RG6U with solid bare copper center conductor and Dual shield rated to 3GHz is our minimum 
recommendation.  Use 3GHz rated compression type female F Connectors to terminate the ends. 
 
Check with your Modem supplier for proper types of cables they may recommend.   

 
Typical Connector Box on DataSAT Antenna - Roof Mounting Plate 

 

A.

 

Antenna Control Cable Connection.  Snap together Male (33482-1201 Molex) Antenna Side 
and Female (33472-1201 Molex) Control Cable to ACU-2 Antenna Controller. 

B.

 

RX Cable to ACU-2 Antenna Controller.  From LNB Black RG-6 Coax Cable.  Labeled RX. 

C.

 

TX Cable to Modem (if installed) or HPA Out.  To BUC White RG-6 Coax Cable. Labeled TX. 

 
If additional assistance is required to connect an external Modem and Router to this system you 
should contact your Bandwidth Service Provider (ISP) and/or find a local IT Technician for 
assistance. 
 
RF Mogul may be able to provide some limited assistance on some systems when basic wiring and 
network configurations are used.  Because many companies require additional securities on their 
networks our assistance will be limited. 
 

System Wiring is complete. 

Содержание DataSAT ACU-2














Отзывы: