RF Innovations RFI-148 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 43

RF Innovations RFI-148 Скачать руководство пользователя страница 9

Configuration

RFI-148 250W VHF Paging Transmitter User Manual

Page 9 of 43

3.

Configuration

3.1 Overview

The RFI-148 250 provides six interfaces that allow the transmitter to be configured and diagnostic
information to be monitored:



Cruise Control management interface:

All configuration and diagnostics parameters can be

accessed using the Windows-based Cruise Control Graphical User Interface (GUI).



SNMP interface:

Support for diagnostics using SNMP.



Terminal menu interface:

A navigable menu system is available that has all the configuration and

diagnostics that Cruise Control provides.



AT command interface:

The AT command interface provides a subset of the configuration and

diagnostic information available over Cruise Control with ASCII Hayes attention commands.



Front panel interface:

The front panel consists of five status LEDs and a transmit power gauge.



LIU interface:

The combined LIU interface has digital inputs and alarm outputs for limited

configuration and diagnostic output.

3.2 Cruise Control

The following sections briefly outline how to use Cruise Control with the paging transmitter. For more
information see the Cruise Control User Manual. Figure 2 below is a typical screenshot of the Cruise Control
interface running on Windows 7.

«
...
7
8
9
10
11
...
»

Содержание RFI-148












































Отзывы:

Нет отзывов