manualshive.com logo in svg

RF Innovations RFI-148, Руководство пользователя, Страница: 32 / 43

Поделиться
Скачать
RF Innovations RFI-148 Скачать руководство пользователя страница 32

 
 

Appendix C Management Reference

 

RFI-148 250W VHF Paging Transmitter User Manual 

Page 32 of 43 

rfiCrFltsFltIdxTable 
rfiCrFltsFltIdxEntry 
rfiCrFltsFltIdxIndex 

Table containing configuration and status of all fault conditions. 

rfiCrFltsFltNm 

Name of the fault in this row of the table. 

rfiCrFltsFltStts 

Indicates whether or not this fault condition is currently active. 

rfiCrFltsActvDrtn 

Duration for which this fault has been active, or 0 if the fault is not 
active. 

rfiCrFltsFltActn 

Configured action to be taken when this fault occurs. 

rfiCrFltsCntr 

The  number  of  times  this  fault  has  occurred  since  the  statistics 
were reset. 

Sensors 

rfiCrSnsMnSttsPrmTable 
rfiCrSnsMnSttsPrmEntry 
rfiCrSnsMnSttsPrmIndex 

Table of parameters associated with sensors. 

rfiCrSnsMnCrrVl 

Current measured sensor value. 

rfiCrSnsMnMxVl 

Maximum possible sensor value. 

rfiCrSnsMnMnVl 

Minimum possible sensor value. 

rfiCrSnsMnCrrStt 

Current fault status associated with this sensor. 

rfiCrSnsMnUppCtff 

Upper  cutoff  value  for  this  sensor.  Measurements  which  exceed 
this cutoff cause a fault. 

rfiCrSnsMnLwCtff 

Lower cutoff value for this sensor. Measurements lower than this 
cutoff cause a fault. 

Identity 

rfiCrIdntGtSrlNmbr 

Factory assigned serial number for this device. 

rfiCrIdntGtMnfctrDt 

Date on which this device was manufactured. 

rfiCrIdntApprvlCd 

International type approval code which applies to this device. 

rfiCrIdntUptmHrs 

An approximation of the total number of hours that this device has 
been powered up. 

rfiCrIdntGtFrmwrVrStr 

Version information for the firmware loaded in this device. 

Table 13: SNMP Diagnostic Parameters 

Содержание RFI-148












































Отзывы:

Нет отзывов