manualshive.com logo in svg

RF Innovations RFI-148, Руководство пользователя, Страница: 17 / 43

Поделиться
Скачать
RF Innovations RFI-148 Скачать руководство пользователя страница 17

 
 

Operation

 

RFI-148 250W VHF Paging Transmitter User Manual 

Page 17 of 43 

4. 

Operation 

4.1 Serial Port Operation 

4.1.1 Overview 

The RFI-148 250 has two DCE RS-232 serial ports. The front serial port has a female DE9 connector (DCE) 
and the rear serial port has a male DE9 connector (DTE). The serial port pin outs can be found in Appendix 
A.3 on page 26. 

The main port (at the back of the transmitter) supports: 

 

TX, RX, and GND. 

 

RTS and DTR inputs. 

 

CTS and DCD outputs. 

The auxiliary (at the front of the transmitter) port supports: 

 

TX, RX, and GND. 

4.1.2 Configuration 

Both main and auxiliary serial ports support the following configuration options: 

 

Baud rate: 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600 or 115200. 

 

Data bits: 7 or 8 

 

Parity: None, odd, or even 

 

Stop bits: 1 or 2 

4.1.3 Statistics 

Statistics  are  maintained  for  both  serial  ports.  These  statistics  are  listed  in  Table  12  in  Appendix  C.1.  All 
statistics are reset if power is removed. 

These  statistics  may  be  useful  in  troubleshooting.  For  example,  Rx  framing  errors  may  indicate  that  the 
serial port configuration does not match the serial port configuration of the DTE. 

4.2 Ethernet Operation 

4.2.1 Overview 

The  paging  transmitter  has  one  10BASE-T/100BASE-TX  Ethernet  port.  Auto-negotiation  of  link  speed  is 
supported, including duplex mode. There is also a software override for forcing the parameters of the link. 

Содержание RFI-148












































Отзывы:

Нет отзывов