manualshive.com logo in svg

RF Innovations RFI-148, Руководство пользователя, Страница: 7 / 43

Поделиться
Скачать
RF Innovations RFI-148 Скачать руководство пользователя страница 7

 
 

Installation

 

RFI-148 250W VHF Paging Transmitter User Manual 

Page 7 of 43 

2.3 Product Installation 

The back panel of the paging transmitter is shown below in Figure 1. 

 

 

 

1. System 

Ground 

 

2. RF Output 

3. External 

Frequency 

 

4. Ethernet 

5. DC Input 

24 V Nominal 

 

6. DC SW 

 

7. RF Diag 

8. LIU 

Interface 

 

9. RS232 

 

Figure 1: Paging Transmitter Back Panel 

 

1.

 

System Ground:

 External connection for system ground.

 

2.

 

RF Output:

 Modulated RF output from the paging transmitter. N-type female connector.

 

3.

 

External  Frequency:

  External  reference  input  for  accurate  channel  synthesis.  BNC  female 

connector.

 

4.

 

Ethernet:

 Ethernet connection for configuration and diagnostics over UDP. RJ45 connector.

 

5.

 

DC Input 24 V Nominal:

 

20-31.2 V DC Input voltage. Terminal block connector.

 

6.

 

RF Diag:

 

Sniffer port for diagnostics. BNC female connector.

 

7.

 

DC SW:

 

Power switch.

 

8.

 

LIU Interface:

 

Combined alarm and encoder interface. DC-37 female connector.

 

9.

 

RS-232:

 

Main serial port. DE-9 female connector.

 

Содержание RFI-148












































Отзывы:

Нет отзывов