REVV Dynamis 7-40 Скачать руководство пользователя | Manualshive

Страница: 14 / 36

background image

Revv Owner’s Manual - 14

Impedance & Speaker Jacks

The amplifier must always be connected to a speaker cabinet or load

when it is powered up. This amplifier can be used with cabinets that

provide a load of 4, 8 & 16 ohms.

Note to combo users: The combo can only be used with external cabi-

nets of 4 or 8 ohms

Because the amplifier provides multiple speaker jacks, it can also power

2 cabinets directly from the amplifier, but the impedance will need to be

set correctly.

Most setups are simple, one cabinet plugged into the amp, set the

impedance to that marked on the cabinet & you’re ready to go! Howev-

er, when it comes to adding more cabinets to the rig, more care must be

taken to prevent damage. Most rigs will not utilize more than 2 cabinets

so we won’t go beyond 2 cabinets here.

3.3

«
...
12
13
14
15
16
...
»

Содержание Dynamis 7-40





































Отзывы:

Нет отзывов

Похожие инструкции для Dynamis 7-40

Бренд: Randall Страницы: 9

Бренд: Accuphase Страницы: 33

Бренд: Conrad-Johnson Страницы: 12

Бренд: Omron Страницы: 103

Бренд: NJS Страницы: 8

redback A 4140 2 x 100W

Бренд: Altronics Страницы: 4

ATLONA AT-RON-442

Бренд: Panduit Страницы: 12

Бренд: Veloce Страницы: 15

Бренд: Com-Power Страницы: 15

Бренд: Alpine Страницы: 18

Jazz Chorus JC-90

Бренд: Roland Страницы: 10

AXYS Octadrive DSP-DN

Бренд: Harman Страницы: 20

Бренд: Macrom Страницы: 17

AFD100 Slash Signature

Бренд: Marshall Amplification Страницы: 6

Бренд: JET CITY AMPLIFICATION Страницы: 18

Bassman Bassman 100

Бренд: Fender Страницы: 16

Reference Amplifier

Бренд: Genesis Страницы: 2

Бренд: Wyred 4 Sound Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды