background image

Revv Owner’s Manual - 30

Foot Switch 

The Revv footswitch can be configured to either operate as a normal 

footswitch (with some bonuses) or a tool to quickly recall presets on the 

amplifier.

Control Mode - select between clean,& gain channels, gain dynamic 

modes, fx loop on/off, solo boost on/off, reverb on/off + its decay level, & 

a master mute function

Preset Mode - select combinations of channel & switch pos on/off 

states that can be recalled with one button press.

Note: The footswitch will always be updated should a change be made 

on the amplifier front panel. Panel controls override the footswitch.

Note: To switch between modes, press & hold footswitch button 1 for 2 

seconds. The LEDs will all illuminate then switch to the settings in the 

other mode. All settings will be retained when switching between modes. 

Hook up 

The footswitch is connected to the rear of the amplifier with a shielded 

Ethernet cable & very rigid connectors. The amplifier & footswitch will 

work with any Ethernet cable should you be in a pinch, but the Revv 

cable is always recommended for best performance. 

It is recommended that the footswitch be connected to the amp with the 

power off, but should you plug it in during amplifier use, it will power up & 

automatically set itself to the amps current settings. Upon power up, all 

LEDs will turn on for a couple of seconds as it initializes. Once complete, 

the foot pedal will set itself to the amplifier’s current configuration. 

7.0

7.1

Содержание Dynamis 7-40





































Отзывы: