Response SA5 E Скачать руководство пользователя страница 39

39

Maintenance

Your  Alarm  System  requires  very  little  maintenance.

However, a few simple tasks will ensure its continued

reliability and operation.

Solar Siren

1. It is recommended that the Solar Panel on the top of

the siren housing should be cleaned at least twice 

a year, preferably in the Spring and Autumn, using a

soft  damp  cloth.    Do  not  use  abrasive,  solvent

based or aerosol cleaners.  Do not attempt to clean

inside the unit or allow water to enter the unit.

This  will  ensure  that  the  Solar  Panel  does  not

become affected by the build up of excessive dirt

and receives all the available light.

2. The Solar Siren should not be left for long periods

with  the  batteries  connected,  unless  the  unit  is

able  to  receive  sufficient  light  to  maintain  the

battery  charge.    Failure  to  maintain  charge  to  the

unit will result in the rechargeable battery running

unacceptably low.  Should this occur, the unit must

be  recharged  from  a  7.5Vdc/100mA  supply  (e.g.

from  a  mains  adaptor  power  supply).    When  re-

powering  the  Solar  Siren  fit  a  new  9V  PP3  leak

proof Alkaline power-up battery to ensure that the

Unit receives sufficient power until the solar panel

can recharge the main battery.

3. The  main  rechargeable  battery  has  a  typical  life

of  3-4  years  and  needs  no  maintenance  during

this period, provided the battery is kept charged.

The  battery  will  be  damaged  if  it  is  stored  in  a

discharged state for long periods.

Control Panel

The  rechargeable  batteries  have  a  typical  life  of  3 - 4

years  and  need  no  maintenance  during  this  period,

provided they are kept charged.  The batteries will be

damaged  if  they  are  stored  in  a  discharged  state  for

long periods.

Detectors And Remote Control 

The  Detectors  require  very  little  maintenance.    The

batteries  should  be  replaced  once  a  year  or  when  a

low battery status is indicated.

IMPORTANT:    Should  you,  for  any  reason,  have  to

completely power-down the system (e.g. to move the 

system  to  a  new  premises)  first  put  the  system  into

Test  mode  before  removing  the  Control  Panel  cover

and  disconnecting  the  power  supply  and  backup

batteries.    To  power-down  the  Solar  Siren  undo  the

fixing screw on the bottom edge and remove the front

cover.    As  the  cover  is  removed  the  Siren’s  Tamper

switch  will  activate,  immediately  cancel  the  alarm

using  the  Remote  Control.    Disconnect  both  the

rechargeable battery and initial power-up battery and

ensure that the solar panel is covered with a light proof

material to prevent it being energised.

Batteries

Before  removing  the  battery  cover  on  any  device  to

replace the battery, ensure that the system is put into

Test mode to avoid initiating an Alarm.

The  specifications  for  replacement  batteries  are  as

follows:

Note:

Where  applicable  only  fit  PP3  Alkaline  type

batteries.    Rechargeable  batteries  should  NOT  be

fitted.

Disposal and Recycling

Disposal  of  this  product  is  covered

by the Waste Electrical or Electronic

Equipment (WEEE) Directive.

It should not be disposed of with other household

or commercial waste.

At  the  end  of  its  useful  life  the  packaging  and

product  should  be  disposed  of  via  a  suitable

recycling centre.  Please contact your local authority

or  the  retailer  from  where  the  product  was

purchased for information on available facilities.

DO NOT BURN.

The  Rechargeable  Batteries  contain  Sulphuric  Acid  –

DO NOT ATTEMPT TO OPEN THE CASING.

Remote Controls

1 x 3V CR2032 Lithium Cells
(or equivalent)

Magnetic Contact

2 x 3V CR2032 Lithium Cells

Detectors

(or equivalent)

PIR Movement

1 x 9V PP3 Alkaline

Detectors

Содержание SA5 E













































Отзывы: