Repotec G Series Скачать руководство пользователя страница 30

Страница: 30 / 42

TROUBLESHOOTING

Basic

Troubleshooting

Tips

Most problems are caused by the following situations.

Check for these items first when starting your

troubleshooting:



Connecting to devices that have a fixed full-

duplex configuration.

The RJ-45 ports are configured as “Auto”. That is, when

connecting to attach devices, the switch will operate in

one of two ways to determine the link speed and the

communication mode (half duplex or full duplex):

◆

If the connected device is also configured to Auto,

the switch will automatically negotiate both link

speed and communication mode.

◆

If the connected device has a fixed configuration, for

example 100Mbps, at half or full duplex, the switch

will automatically sense the link speed, but will

default to a communication mode of half duplex.

Because the GEPOEL2P-ESW10G Switch devices

behave in this way (in compliance with the IEEE802.3

standard), if a device connected to the switch has a

fixed configuration at full duplex, the device will not

connect correctly to the switch. The result will be high

error rates and very inefficient communications

between the switch and the device.
Make sure all devices connected to the

GEPOEL2P-ESW10G Switch devices are configured to

auto negotiate, or are configured to connect at half

duplex (all hubs are configured this way, for example).



Faulty or loose cables.

Look for loose or obviously

faulty connections. If they appear to be OK, make sure

the connections are snug. If that does not correct the

problem, try a different cable.



Non-standard cables.

Non-standard and miswired

cables may cause network collisions and other network

problems, and can seriously impair network

performance. Use a new correctly-wired cable. For

pinouts and correct cable wiring. A category 5 cable

tester is a recommended tool for every 100Base-TX

and 1000Base-T network installation.



Improper Network Topologies.

It is important to

make sure you have a valid network topology. If you no

longer experience the problems, the new topology is

probably at fault. In addition, you should make sure

that your network topology contains

no data path

loops.

Publication date: Sept, 2015

Revision A1

Содержание G Series











































Результаты поиска

Содержание G Series

Отзывы:

Похожие инструкции для G Series

Бренды по названию

Популярные бренды

Repotec G Series, Руководство по установке и началу работы

Результаты поиска

Содержание G Series

Отзывы:

Похожие инструкции для G Series

Бренды по названию

Популярные бренды