Repotec G Series Скачать руководство пользователя страница 31

Страница: 31 / 42



Check the port

configuration.

A port on your Switch may not be operating as you expect

because it has been put into a “ blocking” state by

Spanning Tree, GVRP (automatic VLANs), or LACP

(automatic trunking). (Note that the normal operation of

the Spanning Tree, GVRP, and LACP features may put the

port in a blocking state.) Or, the port just may have been

configured as disabled through software.

Troubleshooting Chart

Symptom

Action

POWER LED is Off

◆

Check connections between the switch, the power

cord and the wall outlet.

◆

Contact your dealer for assistance.

Link LED is Off

◆

Verify that the switch and attached device are

powered on.

◆

Be sure the cable is plugged into the switch and

corresponding device.

◆

If the switch is installed in a rack, check the

connections to the punch-down block and patch

panel.

◆

Verify that the proper cable types is used and its

length does not exceed specified limits.

◆

Check the adapter on the attached device and cable

connections for possible defects. Replace the

defective adapter or cable if necessary.

Publication date: Sept, 2015

Revision A1

Содержание G Series











































Результаты поиска

Содержание G Series

Отзывы:

Похожие инструкции для G Series

Бренды по названию

Популярные бренды

Repotec G Series, Руководство по установке и началу работы

Результаты поиска

Содержание G Series

Отзывы:

Похожие инструкции для G Series

Бренды по названию

Популярные бренды