manualshive.com logo in svg

Renesas H8S/2437, Руководство по оборудованию

Характеристики микроконтроллера Renesas H8S/2437 включены в бесплатное "Hardware Manual", которое можно скачать с нашего сайта. Это подробное руководство поможет пользователям ознакомиться с функционалом устройства и его возможностями. Скачивайте "manual" прямо сейчас с manualshive.com.

Поделиться
Скачать
background image

 

Rev. 1.00, 09/03, page 75 of 704 

 

5.3.6 

Software Standby Release IRQ Enable Register (SSIER) 

SSIER selects the 

IRQ

 pins used to recover from the software standby state. 

Bit 

Bit Name 

Initial Value  R/W 

Description 

7 

6 

5 

4 

3 

2 

1 

0 

SSI7 

SSI6 

SSI5 

SSI4 

SSI3 

SSI2 

SSI1 

SSI0 

0 

0 

0 

0 

0 

1 

1 

1 

R/W 

R/W 

R/W 

R/W 

R/W 

R/W 

R/W 

R/W 

Software Standby Release IRQ Setting 

These bits select the 

IRQn

 pins used to recover from 

the software standby state. 

0: IRQn requests are not sampled in the software 

standby state (Initial value when n = 7 to 3). 

1: When IRQn request occurs in the software standby 

state, the chip recovers from the software standby 
state after the elapse of the oscillation settling time 
(Initial value when n = 2 to 0). 

 

 

5.4 Interrupt 

Sources 

5.4.1 

External Interrupt Sources 

There are nine external interrupts: NMI and IRQ7 to IRQ0. These interrupts can be used to restore 
the chip from software standby mode. 

NMI Interrupt: Nonmaskable interrupt request (NMI) is the highest-priority interrupt, and is 
always accepted by the CPU regardless of the interrupt control mode or the status of the CPU 
interrupt mask bits. The NMIEG bit in INTCR can be used to select whether an interrupt is 
requested at a rising edge or a falling edge on the NMI pin. 

IRQ7 to IRQ0 Interrupts: Interrupts IRQ7 to IRQ0 are requested by an input signal at pins 

IRQ7

 

to 

IRQ0

. Interrupts IRQ7 to IRQ0 have the following features. 

•

 

Using ISCR, it is possible to select whether an interrupt is generated by a low level, falling 
edge, rising edge, or both edges, at pins 

IRQ7

 to 

IRQ0

. 

•

 

Enabling or disabling of interrupt requests IRQ7 to IRQ0 can be selected with IER. 

•

 

The interrupt priority level can be set with IPR. 

•

 

The status of interrupt requests IRQ7 to IRQ0 is indicated in ISR. ISR flags can be cleared to 0 
by software. 

 

When IRQ7 to IRQ0 interrupt requests occur at low level of 

IRQn

, the corresponding 

IRQ

 should 

be held low until an interrupt handling starts. Then the corresponding 

IRQ

 should be set to high in 

the interrupt handling routine and clear the IRQnF bit (n = 0 to 7) in ISR to 0. Interrupts may not 
be executed when the corresponding IRQ

 

is set to high before the interrupt handling starts. 

Содержание H8S/2437











































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для H8S/2437

Qualys GUARD Quick Start Manual preview
GUARD
Бренд: Qualys Страницы: 2
TE Connectivity InterReach Fusion ADCP-77-044 Manual preview
InterReach Fusion ADCP-77-044
Бренд: TE Connectivity Страницы: 236
Idis DR-8400 Installation Manual preview
DR-8400
Бренд: Idis Страницы: 31
D3 DesignCore RVP-TDA3 Series Quick Start Manual preview
DesignCore RVP-TDA3 Series
Бренд: D3 Страницы: 34
Thermalright AXP-100H MUSCLE Manual preview
AXP-100H MUSCLE
Бренд: Thermalright Страницы: 36
ebm-papst D3G146-LT13-30 Operating Instructions Manual preview
D3G146-LT13-30
Бренд: ebm-papst Страницы: 11
YASKAWA PG-Z2 Instructions Manual preview
PG-Z2
Бренд: YASKAWA Страницы: 15
DAD DXZ48 User Manual preview
DXZ48
Бренд: DAD Страницы: 16
Addonics Technologies ADSA2 Installation Manual preview
ADSA2
Бренд: Addonics Technologies Страницы: 1
pivotal COMMWARE ECHO 5G How To Set Up preview
COMMWARE ECHO 5G
Бренд: pivotal Страницы: 2
Supermicro Optane Persistent Memory 200 Series User Manual preview
Optane Persistent Memory 200 Series
Бренд: Supermicro Страницы: 54
B&B Electronics 4 Channel Input Buffer Board SDAIBB Product Manual preview
4 Channel Input Buffer Board SDAIBB
Бренд: B&B Electronics Страницы: 22
Multitech ISI608PC Owner'S Manual preview
ISI608PC
Бренд: Multitech Страницы: 81
Lindy 32116 User Manual preview
32116
Бренд: Lindy Страницы: 12
ST STA309A Operation Manual preview
STA309A
Бренд: ST Страницы: 67
Cooler Master MCY-C3P1-KWNN Manual preview
MCY-C3P1-KWNN
Бренд: Cooler Master Страницы: 4
NUROTRON CS-10A Operation Manual preview
CS-10A
Бренд: NUROTRON Страницы: 16
IBM TSO/E REXX User Manual preview
TSO/E REXX
Бренд: IBM Страницы: 242

Бренды по названию

Популярные бренды

Загрузить еще бренды