REMKO CMF 120 Скачать руководство пользователя страница 77

Страница: 77 / 88

Spare parts list outdoor module CMF/CMT 160

Nr.

Designation

CMF 160

CMT 160

EDV-Nummer

Compressor

1120082

Laminated heat-exchanger

1120083

Four-way switching valve

1120084

Shut-off valves

1120085

Fan blade

1120086

Cover panel

1120087

Side panel, left

1120088

Front panel

1120089

Fan protection guard

1120090

Side panel, right rear

1120091

Side panel, right front

1120200

Cover, rear

1120201

Cover, front

1120202

Recessed grip

1120203

Spare parts (not illustrated)

Grille, rear

1120204

Fan motor

1120206

Sensor

Available only by request with the device no.

Control board

Available only by request with the device no.

Mains filter board

Available only by request with the device no.

Power electronics

Available only by request with the device no.

When ordering spare parts, please state the computerised part no., device number and device type (see

type plate)!

Содержание CMF 120

























































































Результаты поиска

Содержание CMF 120

Отзывы:

REMKO CMF 120, Руководство по сборке и эксплуатации, Страница: 77 / 88

Результаты поиска

Содержание CMF 120

Отзывы: