manualshive.com logo in svg

REMKO CMF 120, Руководство по сборке и эксплуатации, Страница: 48 / 88

Поделиться
Скачать
REMKO CMF 120 Скачать руководство пользователя страница 48

8 

Elektrical connection

8.1  General notes

n

It is necessary to lay a power-supply cable

both to the outdoor unit and, separately, to the

indoor unit.

n

Power to the indoor unit may not be discon-

nected by the power company (Frost protec-

tion).

n

All indoor- and outdoor modules series CMF/

CMT 120 require a single-phase power supply

at 230 V / 50 Hz.
The outdoor modules series CMF/CMT 160

require a three-phase power supply at 400 V /

50 Hz.

n

The electrical connection between outdoor-

and indoor units is made using four-wire con-

trol cable.

n

Where applicable, a separate power supply

shall be provided to the indoor unit for electric

booster heating.

n

The heat pump manager needs to know

whether a power-company release- or off-

period is in effect. An electrically-isolated

switch must be installed for this purpose. (An

open switch signifies power available, an open

switch, off-time.)

n

In the chapter "Connection diagram, terminal

configuration" in this manual can be found a

connection schematic along with corre-

sponding circuit diagrams.

n

Special rates for heat pumps may be offered

by the power company (PSC).

n

Ask your local power company about the

details of any rates that might be available.

 DANGER!

All electrical installation work must be done by

an electrician.

 WARNING!

Always note the currently applicable VDE

guidelines and the notes in TAB 2007. The size

and type of the fuse are to be taken from the

technical data.

 WARNING!

All cable sizes are to be selected according to

VDE 0100. Special attention should be given to

cable lengths, cable type and the kind of instal-

lation. The information in the connection dia-

gram and in the system overview are to be

seen as an acceptable installation possibility

only in a standard case!

 NOTICE!

Make sure to connect the outdoor unit neutral

connector properly, otherwise the varistors on

the line-filter circuit board will be destroyed.

 

Check all plugged and clamped terminals to

verify that they are seated correctly and make

permanent contact. Tighten as required.

 

 

 

REMKO CMF/CMT

 

 

48

Содержание CMF 120

























































































Отзывы:

Нет отзывов