Relcross 9130 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 24

Relcross 9130 Скачать руководство пользователя страница 9

Page 9 of 24

February 2006

Ver 0

ARM AND COVER INSTALLATION (Cont)

6.5.2 For pull systems, slide the pull arm roller into the track, insert a track cap

on each end of the track, and attach the track to the door.

Pull Arm

6.6

Adjust the arm

6.6.1 For pull systems, remove the locking screw from the arm

6.6.2 For the push system remove the locking screw from the arm

Pull

Arm

Push

Arm

6.6.3 Keep the door in the full open position and adjust the arm length as

necessary to align the door at 90 degrees from closed. When the arm is adjusted to
the correct length, tighten up the8 mm socket head screw that secures the arm to
the operator spindle and ensure this is secure, then tighten the arm locking screw

6.7

Turn off the power operator switch. The door closes

6.8

Remove the jumper from the control box T27, T28

6.9

Test the operator (See operational check” on page 11) and continue with step 6. 10

6.10 Adjust the operator as required( see “Operator Adjustment” on page 12) and

continue with step 6.11

«
...
7
8
9
10
11
...
»

Содержание 9130

























Отзывы:

Нет отзывов