Relcross 9130 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 24

Relcross 9130 Скачать руководство пользователя страница 16

Page 16 of 24

February 2006

Ver 0

10

9100 SERIES

VER 4.0 SOFTWARE

10.1. OPERATION.................................................................................................... 17

10.1.1. Sizing ............................................................................................................ 17
10.1.2. Auto Reverse on open................................................................................... 17
10.1.3. Standard

operation ........................................................................................ 18

10.2. FUNCTION

SELECTION................................................................................ 18

10.2.1. Standard

(0)................................................................................................... 18

10.2.2.  Lock in OFF Only (1) ................................................................................... 18
10.2.3.  Lock in 1 Way Only (2) ................................................................................ 18
10.2.4.  PNG in OFF (3) ............................................................................................ 18
10.2.5.  Door closes and Unlocks in Fire Alarm (4).................................................. 18

10.3. FUNCTION

CHART........................................................................................ 18

10.4. CONTROL

BOX

SETUP ................................................................................. 18

10.5.

9100 Series

WIRING .........................................................................

.....

.......... 18

«
...
14
15
16
17
18
...
»

Содержание 9130

























Отзывы:

Нет отзывов