Relcross 9130 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 24

Relcross 9130 Скачать руководство пользователя страница 17

Page 17 of 24

February 2006

Ver 0

10.1 OPERATION

10.1.1 Sizing

From start up (size) the door will activate from morning

entry (24Hrs,T9, T10) regardless of key switch position, 1
Way input (T27,T28) with key switch in one way. 2 Way input
(22, T23) with key switch in two way, or key switch Hold
Open. The first movement will be in the open direction - The
speed of the sizing cycle is automatic and cannot be set from
a potentiometer the door drives opened to the full open
position where the system sets the counter to full open. The
door closes at close speed then latch up to closed position
where the system sets the counter for closed position. From
these two parameters opened and closed position the system
calculates all the other parameters it requires for normal
operation i.e. latch position back check position etc.

•

Notes

If the encoder is connected for opposite direction or

faulty or disconnected the door will operate erratically
continuously opening ½ way closing latching and re-opening.
This will continue to occur until power is switched off

10.1.2 Auto Reverse on open

The auto reverse open is set from the Back check

position pot. This sets the level of current required to trip the
door as it is opening.

«
...
15
16
17
18
19
...
»

Содержание 9130

























Отзывы:

Нет отзывов