Relcross 9130 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 24

Relcross 9130 Скачать руководство пользователя страница 2

Page 2 of 24

February 2006

Ver 0

1. GENERAL.................................................................................................................. 2
2. REPLACEMENT PARTS AND SYSTEM COMPONENTS ................................... 2
3. PRE-INSTALLATION SITE AND PRODUCT CHECK ......................................... 4
4. OPERATOR

INSTALLATION ................................................................................. 5

5. WIRING...................................................................................................................... 7
6. ARM AND COVER INSTALLATION ..................................................................... 8
7. OPERATIONAL

CHECK ........................................................................................ 11

8. OPERATOR

ADJUSTMENT .................................................................................. 12

9. RELEASE FOR SERVICE ...................................................................................... 15
10.

9100 SERIES

VER 4.0 SOFTWARE.................................................................

.....

16

1 GENERAL

The

9100

is an automatic electromechanical swing door operator for use on

Hinged, centre pivoted, and offset pivoted doors. The controller is a microprocessor based
system, tracking the door position at any time during the cycle. When activated the

9100

drives the door to the full open position creating the potential energy in the
spring. When closing the electrical power is reduced and the door closes by controlling
the potential energy release in the spring force. The activating circuit opens the door from
any position on the closing swing. During power failure the

9100

acts as a manual

door closer (size 3). Door opening and closing cycles, including opening speed, back
check speed, hold open time delay, closing speed, and latch position are adjustable.

WARNING

Always disconnect main power to the operator prior

to servicing or cleaning

Warning

.

2 REPLACEMENT PARTS AND SYSTEM COMPONENTS

Description

Part No

Control Box

710026 – XXX

Gear Box

9100-000

Cover

2550.CP.SA (95171-975R)

Pull Arm Assembly

2550.T.AP.SE (95005-975)

Push Arm Assembly

2550.AP.SE (95085-975)

«
1
2
3
4
...
»

Содержание 9130

























Отзывы:

Нет отзывов